1 / 39

The TEAMMATE

The TEAMMATE. A Mechanical Regenerative Braking Design Project Winter 2013 Team Eight . The Team. John El- Tawil Colin MacKenzie Michael Matthews Alan Robinson. Dr. Marek Kujath. Supervisor. Outline. Introduction Design Testing Design Requirements Budget

chiku
Download Presentation

The TEAMMATE

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. The TEAMMATE A Mechanical Regenerative Braking Design Project Winter 2013 Team Eight

  2. The Team • John El-Tawil • Colin MacKenzie • Michael Matthews • Alan Robinson • Dr. MarekKujath Supervisor

  3. Outline • Introduction • Design • Testing • Design Requirements • Budget • Summary & Recommendations

  4. Scope • Design/build a mechanical regenerative braking system • Capture energy dissipated during braking of a bicycle • Lower input energy to accelerate from stop • Improve rider efficiency

  5. The Design

  6. The Spring • System uses a spiral torsional spring • Issue: Input is CW Output is CCW • Solution: Charge outside Release inside Figure 1 – Spiral Torsional Spring

  7. How the Spring will Work 1. 2. 3. 4. Figure 2 – Spring Dynamics

  8. Custom Axle Figure 3 – Standard Hub (Shimano, 2013) Figure 4 - Custom Hub

  9. Custom Axle Figure 5 – Custom Axle

  10. The System Figure 6 – The System

  11. Input Shaft Figure 7 – The Input Shaft

  12. The System Figure 8 – The System

  13. Output Shaft Figure 9 – The Output Shaft

  14. Manual Control / Operation Figure 10 – The Manual Control Triggers

  15. Testing • Friction losses from system • Weight losses from the system • Energy gained from the spring Figure 11 – Testing

  16. Test # 1: Friction Losses • Energy could be lost in the system from bearing friction • A speed test was run 5 times with chains attached and detached • Final speeds were averaged and compared to determine if there were losses in energy

  17. Friction Losses Table 1 – Average speed with system not chained Table 2 – Average speed with system chained

  18. Friction Losses Assuming no losses from friction, the final velocities should be the same = 97.2% Losses were minimal with system engaged Therefore friction losses neglected in energy balance

  19. Test # 2: Weight Losses • Energy lost due to added weight of the system(8.98 kg) • Accelerating a mass requires energy • The difference in accelerating the bicycle with and without the system will show the energy taken to accelerate just the system from rest.

  20. Weight Losses Table 3 – Distance and time for acceleration with system Table 4 – Distance and time for acceleration without system

  21. Weight Losses • extra needed to accelerate the system mass after each stop

  22. Test # 3: Energy Gained • Spring ‘’ obtained through testing using torque sensor ratchet () • Rotational angle for a max charge, 270 degrees • Spring’s K and max lower than ideal • Limits system benefits

  23. Testing Results • Rider uses 16.1 J less than they would without the system per acceleration • The total savings will increase based frequency of use • 34 KJ saved per semester for one team member.

  24. Testing Summary • Showed overall net gain in energy while using the “TeamMate” • Energy gain is very low, but can be improved with two simple design improvements: • Reduce system weight (cast iron and steel not required) • Custom torsional spring (higher K and greater • The output chain can slip in high torque situations

  25. Key Design Requirements

  26. Budget

  27. Future Recommendations 4. Different bicycle 5. Custom back rack 6. Better bearings 1. Custom torsional spring 2. Reduce weight 3. Add output tensioner

  28. Acknowledgements • Angus • Albert, Mark • Dr. MarekKujath • Dr. Ted Hubbard, Dr. Clifton Johnston • Ideal Bikes • Cyclesmith • Master Auto • Supermileage Team • Dr. Robert Bauer

  29. Questions? Website: http://poisson.me.dal.ca/~dp_12_08/ Twitter: @MechTeamEight

  30. Key Ring Key Ring

  31. Maximum Torque Required to Accelerate a Bicycle

  32. Assume is based on air resistance at and (1.022 ) NOTE: 5.63 N was increased to 10 N to compensate for relative wind velocity and neglected mechanical losses in bicycle. (9) (10) = 44.0 Nm (11) NOTE: It was later determined through testing that the maximum torque required was approximately 35.0 Nm but to maintain a conservative approach, all following calculations are based on 44.0 Nm.

  33. Safety Factor of Bicycle Chain S.F. = = 1.78

  34. Safety Factor of Bicycle Sprockets S.F =

  35. Safety Factor of Disc Brake Safety Factor

  36. Safety Factor of Spiral Torsional Spring Safety Factor

  37. Safety Factor of Shafts Subjected To Torsion Safety Factor

  38. Safety Factor of Shafts Subjected to Shear Safety Factor

  39. Test # 4: Energy Storage System Efficiency • Compare input and output speeds on the stand • With and without torque resistance

More Related