1 / 16

RS422, RS485, RS423, RS449 and V.35

RS422, RS485, RS423, RS449 and V.35. Introduction . Serial interface standards that support longer cable lengths and higher data rate than RS232. Agenda. Balanced Line Interface RS422 RS485 RS423 RS449 V.35. Vocabulary. Skew Rate

cheng
Download Presentation

RS422, RS485, RS423, RS449 and V.35

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. RS422, RS485, RS423, RS449 and V.35 Data Communications (E&T2760): RS422, RS485, RS423, RS449 and V.35

  2. Introduction • Serial interface standards that support longer cable lengths and higher data rate than RS232. Data Communications (E&T2760): RS422, RS485, RS423, RS449 and V.35

  3. Agenda • Balanced Line Interface • RS422 • RS485 • RS423 • RS449 • V.35 Data Communications (E&T2760): RS422, RS485, RS423, RS449 and V.35

  4. Vocabulary • Skew Rate • Measure the slope of signal transitions between Mark and Space • High skew rate causes interference to adjacent wires within the same cable (i.e. crosstalk) Data Communications (E&T2760): RS422, RS485, RS423, RS449 and V.35

  5. Balanced (Differential) Line Interface • A pair of wires is used to carry each signal. The data is encoded and decoded as a differential voltage between the two lines • Advantages: • the interface is unaffected by differences in ground voltage between sender and receiver • if lines A and B are close together (e.g. in twisted pairs), they will be affected almost identically by external electromagnetic noise, which can then be eliminated at receiver Data Communications (E&T2760): RS422, RS485, RS423, RS449 and V.35

  6. Balanced Line Interface Data Communications (E&T2760): RS422, RS485, RS423, RS449 and V.35

  7. RS422 • Balanced line interface • Mark: VA – VB > +0.2V • Space: VA – VB < –0.2V • Strictly for point-to-point communications • Recommended maximum cable length is 4,000 ft. at 100kbps Data Communications (E&T2760): RS422, RS485, RS423, RS449 and V.35

  8. RS485 • = RS422 with tri-state drivers • Used in multi-drop networks Data Communications (E&T2760): RS422, RS485, RS423, RS449 and V.35

  9. RS423 • Single-ended (unbalanced) • one pair of wires per signal, one of it is GND • crosstalk is further reduced by using lower signal skew rate • Mark: –3.6 to –6V • Space: +3.6 to +6V • Can be used in one-to-many-points communications • Recommended maximum cable length is 40ft. at 100kbps, for 10 receivers Data Communications (E&T2760): RS422, RS485, RS423, RS449 and V.35

  10. RS422, RS423 Speed and Length Limits Source: Beyda, Basic Data Communications, Prentice Hall Data Communications (E&T2760): RS422, RS485, RS423, RS449 and V.35

  11. RS449 • Replace RS232 in high speed synchronous communication between DTE and DCE • Combine both balanced and unbalanced signals on the same interface • RS422: for fast changing signals like TD, RD and Clock • RS423: for slow changing signals like RTS, CTS, DSR, DTR, … etc. • Use a DB37 connector Data Communications (E&T2760): RS422, RS485, RS423, RS449 and V.35

  12. V.35 • = V.10 + V.11 • Widely used to connect high speed (> 56kbps) DCEs in WAN (e.g. T1, Frame Relay, ATM networks) • Combine both balanced and unbalanced signals on the same interface • RS422: for fast changing signals like TD, RD and Clock • RS232: for slow changing signals like RTS, CTS, DSR, DTR, … etc. • Easily recognized by it bulky 34-pin connector Data Communications (E&T2760): RS422, RS485, RS423, RS449 and V.35

  13. V.35 Connector Data Communications (E&T2760): RS422, RS485, RS423, RS449 and V.35

  14. Pin Signal Pin Signal A Chassis Ground B Signal Ground C Request to Send D Clear to Send E Data Set Ready F Receive Line Signal Detect H Data Terminal Ready J Ring Indicator P Transmitted Data (Signal A) R Received Data (Signal A) S Transmitted Data (Signal B) T Received Data (Signal B) U Terminal Timing V Receive Timing A W Terminal Timing X Receive Timing Y Transmit Timing AA Transmit Timing V.35 Signals Data Communications (E&T2760): RS422, RS485, RS423, RS449 and V.35

  15. Summary • RS422 and RS423 support longer cable length at higher data rates than RS232 • RS422: benefit from balanced line interface • RS423: benefit from individual ground return and lower skew rate • RS449 and V.35 combine both balanced and unbalanced signals on the same interface • RS449: RS422 + RS423 • V.35: RS422 + RS232 Data Communications (E&T2760): RS422, RS485, RS423, RS449 and V.35

  16. Where to Get More Information • www.sangoma.com/signal.htm • www.arcelect.com/rs232.htm Data Communications (E&T2760): RS422, RS485, RS423, RS449 and V.35

More Related