1 / 22

Proposal : 2.5 Gbps Radiation Tolerant Serializer Design for the CBM–DAQ in 180 nm CMOS process

Proposal : 2.5 Gbps Radiation Tolerant Serializer Design for the CBM–DAQ in 180 nm CMOS process. Pradeep Banerjee, Dr. T. K. Bhattacharyya, E & ECE Dept., Indian Institute of Technology, Kharagpur 15 th CBM Collaboration Meeting, GSI 12 th - 16 th April 2010. Outline.

charo
Download Presentation

Proposal : 2.5 Gbps Radiation Tolerant Serializer Design for the CBM–DAQ in 180 nm CMOS process

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Proposal: 2.5 Gbps Radiation Tolerant Serializer Design for the CBM–DAQ in 180 nm CMOS process Pradeep Banerjee, Dr. T. K. Bhattacharyya, E & ECE Dept., Indian Institute of Technology, Kharagpur 15th CBM Collaboration Meeting, GSI 12th - 16th April 2010

  2. Outline • New Proposal for a separate Data Aggregation chip • Architecture and Circuit Options for the High speed Serializer • Some aspects of Radiation Tolerant design in deep submicron CMOS • Activities at the RF IC group at AVLSI Lab, IIT KGP 15th CBM Collaboration Meeting

  3. The CBM Generic Read-out Chain DAQchain Detector Sub-System FLES Front-EndBoard Detector Read-OutController Active BufferBoard Data CombinerBoard First LevelEvent Selector FEB ROC DCB ABB FLES Data &Control Data Control Data DCS Sync TNet FEE DAQInterface Local Pre-Processing DigitizationCustom ASIC DAQFLESInterface FPGA Coprocessor Buffering SystemSynchronization Event Selection CPU Farm Slide Info: Walter F.J. Müller, GSI 15th CBM Collaboration Meeting 3

  4. STS Data Rates – Aggregation Very few chip in inner region have hit rate > 32 MHz > 90% of chips have hit rates in 2...16 MHz range AMPLE SCOPE FOR DATA AGGREGATION 31.25 MHz hit rate  2.5 Gbps Au+Au @ 25 AGev107 evt/sec Hit rate per chip Statistics Slide Data from: Walter F.J. Müller, GSI 15th CBM Collaboration Meeting 4

  5. STS FEB Type and Link Distribution • 38 chips exceed 2.0 Gbps: 29 with 2.0 … 2.4; 9 with 2.4 … 3.2; • # of FEBs and type distributions varies for stations Slide Data from: Walter F.J. Müller, GSI 15th CBM Collaboration Meeting 5

  6. Data Aggregation on separate chip - Communication hub • Motivation: • Data Aggregation: In most cases 2,4, or 8 CBM-XYTER chips (FEBa2, FEBa4, FEBa8, resp.) can be aggregated to fill a 2.5 Gbps link • Increase the bandwidth available per link • Reduce the number of Optical Links • Schemes: • Embedded (aggregation integrated in CBM-XYTER) • Data aggregation and Traffic Managementwith a separate Communication Controller Asic  • Clock Distribution • Slow control traffic • Data Readout traffic Communication ‘hub’ 15th CBM Collaboration Meeting 6

  7. Xyter #1 A peep into some feasible ‘Hub’ ASIC Requirements • Capacity for data aggregation from several Readout-ASICs into a single output link • 1 ‘hub’ ASIC may contain 6 high speed Serializers : 6 Tx for data  15 Gbps serviceable data bandwidth • 1 Rx – 1 Tx channel for clock, sync, control • 250 MHz sys clock as Transmit clk  500 Mbps (DDR LVDS) input interface • 5-8 LVDS o/p links (each 500 Mbps) per chip  • FEBa8 case : 1 LVDS link per chip: combinedata of 6 FEBs (48 LVDS links) per Hub • FEBa1 case : All 6 LVDS links (single chip) per Serializer • Cross-Connect Topology: Dynamic load balancing b/w the 6 output links desirable FEB sys_clk HUB Asic Serializer #1 Six 2.5 Gbps o/p links 5-8 LVDS links (500 Mbps) per chip Serializer #2 Xyter #2 Detector i/f #6 #8 PLL Clk Gen clock, sync, control i/f 15th CBM Collaboration Meeting ‘Hub’ Idea: Walter F.J. Müller, GSI 7

  8. High Speed Serializer Core • Design of the following functional blocks: • High speed Serializer (2.5 Gbps) • PLL and Clock generator • Output Driving Logic (impedance matched) • Technology: • CMOS process of interest: UMC 180 nm (Available through Europractice) • Beneficial Features for Radiation tolerant design: • Retrograde wells • Shallow Trench Isolation 15th CBM Collaboration Meeting 8

  9. Serializer “Primer” • Parallel-load Shift register: • Cascade of flip-flops and 2-to-1 multiplexers • Operation speed is limited by: • Clock to Q delay • Mux delay • Flip-flop setup time • Maximum frequency: • 1/(tcq + tmux + tsetup) • Static Flip-Flops: • Operation @ 2.5 Gbps  T = 400 ps • Speed constraint • Can we use Dynamic Flip-Flops? • No, they are sensitive to SEUs • Other high speed options: • Current Mode Logic 15th CBM Collaboration Meeting 9

  10. 2.5 Gbps Serializer ASIC block diagram BIST gen TXP D(0:9) 2.5 Gbps 50 ohm driver Word Mux 10 bit Serializer d(0:9) TXN 250 MHz Tx Clk 1.25 GHz load 2.5 GHz PLL Ref 2.5 GHz Clock Generator PLL Not shown: FIFOs, Arbitration logic (token ring), 8B/10B Encoders 15th CBM Collaboration Meeting 10

  11. Multiple Serializer Core: Design Challenges • Jitter-free Clock signalMinimize noise contribution of VCO (Total serial o/p jitter < 120 ps for BER ~ 10-12) • Switching noise generated by digital logic in ASIC • Constantphase relationship b/w VCO and Sys clock (400 ps bit time) • MultipleSerializer cores per chip: • Power efficiency, ASIC footprint • Sharinga single frequency multiplier among several Serializer cores in the same ASIC : • Distributing multi-gigahertz clocks over an extended distance consumes lot of power • Signal integrity issues  percentage of area saved as a function of the number of cores for a PLL that is half the size of a Serializer core saturates beyond 4 • Careful planning on circuit layout  buffering high speed clock in cascade actually worsens jitter performance • De-Serializer: CDR complexity 15th CBM Collaboration Meeting 11

  12. Serializer – Dual phase Architecture 15th CBM Collaboration Meeting 12

  13. Serializer – Dual phase Architecture … • Word-clock = (1/10) * VCO Clock ( = 2.5 GHz) • Bit-clock = (1/2) * VCO Clock • Multiphase Clock generation for further reduction of clocking speed • Issues: Duty cycle distortion jitter 15th CBM Collaboration Meeting 13

  14. Background – Rad-hard design • Ionizing radiation effects on CMOS ICs: • Total Ionizing Dose (TID) Effects • Issues : threshold-voltage shifts, mobility degradation, and isolation related leakage • Remedy : “Radiation tolerant Layout techniques” – Systematic use of Annular Symmetric Enclosed Layout Transistors (ELT) and p+ guard rings between the n+ diffusions • Single Event Effects (SEE) • Variants: • Non-Destructive : Single Event Upset (SEU), Single Event Transient (DSET) • Destructive : Single Event Latch-Up (SEL) • Issues: • SEU : Depending on the LET, if parasitic charge > node critical charge, a logical switch may occur (bit flip) • DSET : Error rate depends linearly on Clock frequency (glitch) • SEL : Parasitic thyristor structure leading to latch-up • Remedy: • SEU/DSET: Temporal Sampling – Triple Modular Redundancy (TMR), Error Detection and Correction (EDAC);Add Capacitance to sensitive nodes to increase ‘critical charge’ • SEL : Radiation tolerant Layout techniques and usage of p+ guard rings 15th CBM Collaboration Meeting 14

  15. Background cont ... Rad-hard design • Observations/Experience in CBM Radiation Environment: • TID : • MUCH plane 1 (at 130 cm) : deposited energy (rad/CBM-yr) • at perimeter: ~30krad/yr, in center: ~500krad/yr • Not necessary to have all transistors with ELT layout • SEL: • Not seen as an issue in tests so far in deep submicron CMOS • SEU/SET: • MUCH plane 1 (at 130 cm) : fluence hadron E>20 MeV (/cm2/CBM-yr) • at perimeter: ~2·105 h/cm2/s, at center: ~2·106 h/cm2/s • Hadrons flux VERY Significant for SEUs 15th CBM Collaboration Meeting 15

  16. Approach: Work Plan • Freeze System level/Interface Specs • Design an appropriate architecture for the High speed Serializer core • Design and Implementation of the Peripheral cores in UMC 180μm process: • PLL • Clock generator • 50 ohm output Impedance driver • Characterization of UMC 0.18μm CMOS process concerning the vulnerability against SEU / SETs • Testing : • Functionality/Performance : Design of different Testing/Digital blocks: • Pseudo Random Sequence generator (PRSG) • 8B/10B encoder, FIFOs • FPGA devices to program the Serializer Test Configuration • generation of Test data patterns • monitor PLL’s locking state, etc. • Radiation Tolerance 15th CBM Collaboration Meeting 16

  17. 15th CBM Collaboration Meeting 17

  18. 15th CBM Collaboration Meeting 18

  19. 15th CBM Collaboration Meeting 19

  20. 15th CBM Collaboration Meeting 20

  21. Resources Available at AVLSI Lab, IIT KGP 15th CBM Collaboration Meeting 21

  22. THANK YOU FOR YOUR ATTENTION 15th CBM Collaboration Meeting 22

More Related