1 / 22

Modes of Failure

Modes of Failure. solids held together by bonds between their atoms. these bonds can be compressed. or extended. 1/22. Modes of Failure. tension . compression. buckling. shear. bending. stress pattens may be complex but consist of only 3 basic states of stress

boyd
Download Presentation

Modes of Failure

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Modes of Failure • solids held together by bonds between their atoms • these bonds can be compressed or extended 1/22

  2. Modes of Failure • tension • compression • buckling • shear • bending • stress pattens may be complex but consist of only 3 basic states of stress tension - compression - shear 2/22

  3. Tension • state of stress where material • tends to be pulled apart • cable with weight becomes longer under pull • lengthening depends on X-section, length & load • larger the diameter - smaller the elongation 3/22

  4. a steel column under compression shortens as much as a rod of same steel lengthens in tension under same stress Compression • state of stress in which particles • pushed against the others • column under load shortens • squashes • shortening of material 4/22

  5. Compression (cont.) • compression elements very common must channel loads to ground • can have no tension elements but must have compression elements • materials weak in tension often strong in compression • with modern materials of high compressive strength, e.g. steel can build columns much slimmer • but slenderness introduces new problem 5/22

  6. Buckling • as compressive load increases, reach value whereslender elementsinstead of shorteningbuckle& usually break • bucklingis a basic design factor for slender elements in compression • buckling occurs even if load perfectly central • buckling load depends on: material, length, shape of X-section, restraints at ends 6/22

  7. Shear • state of stress in which particles of material slide relative to each other • rivets tend to shear • a hole puncher uses shear to punch • out holes in paper • load on short cantilever tends to • shear beam from wall 7/22

  8. Bending • consider plank loaded as shown • plank ends move down • section between stones deflects up • curve is arc of circle • upper fibres lengthen • lower fibres shorten • middle fibres remain original length - Neutral Axis 8/22

  9. Bending (cont.) • concrete beam fails intension due tobending • may fail indiagonal tension due to shear due to bending 9/22

  10. Behaviour of Materials • stress • strain • elasticity - plasticity - brittleness • safety factors • selecting appropriate materials 10/22

  11. Modes Of Failure - Under Stress • tension • compression • buckling • shear • bending stress patterns complex but consist only of three basic states of stress tension - compression - shear 11/22

  12. elastic or plastic General Load-Deformation Properties Of Materials • application of load produces dimensional changes in a member • member undergoes change in size or shape or both • deformation may be reversible or irreversible 12/22

  13. Stress • internal forcesdeveloped within a structure due to action ofexternal forces • stress is force intensity - force per unit area 13/22

  14. Fe Fe Fe Stress = Force / Area f = F / A Fi = Fe X X Fe Fe Fe Stress (cont1.) • consider member in tension • stress is force intensity -force per unit area 14/22

  15. A load of 1 N on each square metre represents an average stress of 1 N/m2, or 1 Pa 1N 1N 1m 1N 1m 1N 1m 1m 1m 1m 1m Stress (cont2.) • stress is force per unit area 1 pascal = 1 newton per square metre 15/22

  16. 1 MPa = 106 N/m2 = 1 N/mm2 Stress (cont3.) • we use stress in megapascals (MPa) for most materials ( remember 1 m2 = 106 mm2) • we use stress in kilopascals (kPa) for floor loads and foundation pressures (loads distributed over an area) 16/22

  17. stress developed DOES NOT DEPEND ON MATERIAL OF MEMBER Stress (cont4.) • internal force not concentrated at single spot • distributed over entire cross-section • stress in a member depends only on force applied and cross-sectionf = F / A 17/22

  18. Strength of Members • strength depends on many factors • in tension, failure will occur by pulling apart at weakest location • weak spot (point of reduced X-section) determines capacity of whole member • f = F/A higher because of smaller A • if material can sustain stress member will carry load • as load increases stress increases eventually material fails (pulls apart) 18/22

  19. Strain • response to stress • have stress --> get strain • strain to do with change in size or shape ratio of change in size or shape of element to original size or shape 19/22

  20. DL increase in length strain = e = original length L STRAIN (cont.1) • for member subject to simple tensile force • dimensionless - millimetre / millimetre 20/22

  21. STRAIN (cont2.) • determined by: • taking member of known length • subjecting it to a known load • measuring elongation • except for rubber bands, strains very small usually not visible • more a material strains under load - more the structure deflects 21/22

  22. causes stress puts material under strain results in deformation STRESS & STRAIN SUMMARY force 22/22

More Related