1 / 21

EE198B

EE198B. Senior Project class Fall 2001 San Jose State University. Single Crystal Solar Photocell. Team Members: Mack Appleton Sung Min Park Yemane Tsegaye Angel Milano Project Advisor: Dr. David Parent . Project Outline. Introduction Initial Testing Design and Simulation.

bono
Download Presentation

EE198B

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. EE198B Senior Project class Fall 2001 San Jose State University

  2. Single Crystal Solar Photocell Team Members: Mack Appleton Sung Min Park Yemane Tsegaye Angel Milano Project Advisor: Dr. David Parent

  3. Project Outline • Introduction • Initial Testing • Design and Simulation. • Fabrication of Solar Cells • Test Solar Cells • Conclusion

  4. Project Objective • To design, simulate, establish and document a silicon process base-line traveler for the Single Crystal Solar Photocell. • To enhance the relative efficiency of the Solar Photocells by 5%.

  5. Design and Simulation Maximize the efficiency Anti-refraction coating.

  6. Formula & Equations 1. Rs=L/w (2D) 2. Rs = (Rn+) + (Rbar) + (Rcontact) Rn+ = (n+ * S)/(n*b) Rbar = (al*b)/(Wb*n) Rcontact = c/(Wb*b) 3.  = Pm/Pin = (FF*IL*Voc)/Pin 4. FF : Fill Factor (Im*Vm)/(Isc*Voc) 5. P=I*V= (I^2)*R

  7. Design of Models  Large-grid with AR  Large-grid without AR  Small-grid with AR  Small-grid without AR where Large grid : S=3.3 cm, Wb=0.2cm, b=6.6cm, and 2 fingers. Small grid : S=0.75cm, Wb=0.2cm, b=6cm, and 8 fingers

  8. Fabrication of Solar Cells • Diffuse donor region • Apply aluminum coating to front of wafer • Photolithography to define solar cell pattern • Etch aluminum to create solar cell pattern • Apply anti-reflection coating * • Apply aluminum coating to back of wafer • Anneal wafers • Remove outer edges of wafers

  9. Diffuse Donor Region • Spin on phosphorous doped silica glass • Apply 3ml to front of wafer • Spin @ 3000 rpm for 20 seconds • Diffuse in furnace • Heat furnace to 1100oc • Push in wafers ½ inch per 15 seconds • Diffuse for 1 hour • Pull out wafers ½ inch per 15 seconds • Makes wafer into a large diode

  10. Apply Aluminum Coating • Desire 2 microns thickness • Sputter on the aluminum • Accurate and precise • Fast (2 microns onto 8 wafers in 15 min.) • Prone to breaking down - Or - • Evaporate on aluminum • Reliable • Slow (2 microns onto 24 wafers in 3 to 4 hours) • Not very precise

  11. Photolithography • Apply 3ml photo-resist; Spin for 20s @ 5000 rpm • Soft bake for 90oc for 30 minutes • Place solar cell mask on wafer • Place both into wooden and glass holder • Expose under lamp for 2 minutes • Develop for 15 seconds

  12. Etch Aluminum • Etch exposed al using hot sulfuric acid • Rinse with DI water • Remove remaining PR using plasma etch

  13. Apply Anti-reflection Coating • Apply 3ml Titaniumsilicafilm • Spin @ 3000 rpm for 20 seconds • Spreads film to thickness of 1000 angstroms

  14. Anneal Wafers • Anneal for 30 minutes in furnace • Creates ohmic contact between al and Si

  15. Cleave Edges of Wafers • Need to prevent shorting along edge of wafer • Use scribe tool to score along edges of solar cell • Cleave wafer along scoring

  16. Testing the Solar Cells • Scored, or roughened, back of cells • Placed onto roughened aluminum wafer • Used probes to make contacts • One probe onto the corner of the cell’s al grid • One probe onto the al wafer • Tried various methods for making good contacts • Solder paste • Silver paste • Copper tape

  17. Testing the Solar Cells • Illuminated the cell • Used 75W light bulb at 3cm distance • Connected voltmeter to probe terminals • Gives open circuit voltage • Connected current source to probe terminals • Ran current against that being generated by the cells • Measured voltage for different current levels

  18. IV Curves for One Half ofGrid Solar CellsPmax S13A = 41.9 mW Pmax S6A = 49.8

  19. IV Curves for Small Grid Solar CellsPmax S21 = 61.4 mW Pmax S8 = 71.5 mW

  20. Conclusions • AR cells average of 17.8% more efficient • Efficiency increase = (PmaxOLD – PmaxAR)/PmaxOLD • Wanted minimum 5% increase • Easy to follow process • Recommendations • Use the smaller grid • Possible photolithography and etch of back al

More Related