1 / 18

COMMUNICATION SYSTEM EECB353 Chapter 2 (VI) AMPLITUDE MODULATION

COMMUNICATION SYSTEM EECB353 Chapter 2 (VI) AMPLITUDE MODULATION. Dept of Electrical Engineering Universiti Tenaga Nasional. SSB Transmitter.

annona
Download Presentation

COMMUNICATION SYSTEM EECB353 Chapter 2 (VI) AMPLITUDE MODULATION

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. COMMUNICATION SYSTEM EECB353Chapter 2 (VI)AMPLITUDE MODULATION Dept of Electrical Engineering UniversitiTenagaNasional

  2. SSB Transmitter • The design of the SSB transmitter is accomplished in two stages. First we generate a DSBSC signal and then remove the lower sideband to achieve the final SSB result. • Generating the DSBSC Signal • Internally, the balanced modulator generates the AM waveform, which includes the carrier and both sidebands. • It then offers the facility to feed a variable amount of the carrier back into the modulator in anti-phase to cancel the carrier output. • In this way we can balance out the carrier to suppress it completely leaving just the required DSBSC waveform.

  3. Generating DSBSC 450k 453k 456k BM 1 DSBSC 0 3k Audio input Carrier freq, 453kHz

  4. SSB Transmitter • From DSBSC to SSB • The DSBSC signal consists of the two sidebands, one of which can be removed by passing them through a bandpass filter. • The inputs to the balanced modulator comprise the audio inputs from the audio oscillator, which extend from 300Hz to 3.4kHz, and the carrier input. • On the ANACOM 1/1 board this carrier oscillator, although marked as ‘455kHz’, actually needs to operate at a frequency which is a little less than this, around 453kHz. Why is this? • It is to ensure that the upper sideband can pass through the ceramic bandpass filter but the lower sideband cannot pass through.

  5. DSBSC to SSB (1st conversion) 0 3k 450k 453k 456k 453k 456k Audio input BM 1 BPF 1 DSBSC SSBSC Ctr freq = 455kHz BW = 3kHz Carrier freq, 453kHz 453k 455k 456k

  6. SSB Transmitter • The upper sideband can be seen to be within the passband of the ceramic filter but the lower sideband is outside and will therefore be rejected. • The sideband frequencies are quite close to each other and a good quality ceramic filter is required. • A ceramic filter passes only a narrow range of frequencies with a sharp cut-off outside of its passband.

  7. SSB Transmitter • Transmitting the SSB signal – SSB signal that generated before is combined with a 1MHz carrier signal to produce a new DSBSC signal • This signal will now have two new sidebands, • one around 1MHz + 455kHz = 1.455MHz • and the other at 1MHz - 455kHz = 545kHz. • Since these two sidebands are separated by a wide frequency range, the filter design is not critical and a simple parallel tuned circuit is sufficient.

  8. DSBSC to SSB (2nd conversion) 544k 547k 1M 1.453M 1.455M 1.453M 1.456M 453k 456k O/P Amp BM 2 BPF 2 DSBSC SSBSC Ctr freq = 1.455M BW = 3kHz Carrier freq, 1MHz 1.453M 1.455M 1.456M

  9. SSB Transmitter • The 1.455MHz output signal then only requires amplification before transmission. antenna LO =1MHz LO =453kHz Good quality filter audio audio +LO =455kHz 1455kHz

  10. SSB Receiver • The receiver is of the normal superhet design. The first stages are the same as we met for DSBFC. • The incoming signal is amplified by the RF Amplifier and passed to the mixer. • The other input to the mixer is the local oscillator that is running at 455kHz above the frequency to which the receiver is tuned. • The mixer generates sum and difference signals and the lower of the two is the resulting IF signal occupying a range of frequencies around 455kHz. • The audio information must now be separated from these IF frequencies. RF section Mixer IF Section Mixer 2 Audio Amplifier

  11. SSB Receiver • One way of extracting the audio signals is to use a mixer to shift the frequencies. • If a mixer combined an input of (audio + 455kHz) with another input of 455kHz, the resultant outputs would be the usual ‘sum’ and ‘difference’ frequencies. • The ‘sum’ would be (audio + 455kHz) + (455kHz) = (audio + 910kHz) which is far too high a frequency to be of much interest to us. • The ‘difference’ frequency is just what we wanted (audio + 455kHz) - (455kHz) = (audio). LO audio audio + 455kHz audio + 910kHz 455

  12. SSB Receiver • In the ANACOM 1/2, the mixer is called the product detector and the 455kHz input to the product detector is provided by an oscillator called a ‘Beat Frequency Oscillator’ or BFO.

  13. SSB Receiver Sideband inversion Received Signal fIF = fLO + fRF fIF(lsb) = fLO - fRF(usb) = 1.908M – 1.456M = 0.452M fIF(usb) = fLO - fRF(lsb) = 1.908M – 1.453M = 0.455M 1.453M 1.456M 0.452M 0.455M Preselector & RF amp IF Amplifier & BPF Mixer 2 & Product Detector Mixer 1 LPF Audio amp LO BFO 455kHz fLO = fc + fIF = 1.453M + 455k = 1.908MHz SUM : audio + 455 + 455 = XXXX DIFF: audio + 455 – 455 = audio

  14. MT Sem 2 0809 Figure 2: SSB Transmitter • Figure 2 below shows a block diagram of an SSB transmitter. A modulating signal with bandwidth of 3 kHz and centre frequency of 2 kHz as shown is inserted to the first balance modulator input. • What kind of signal generated at the output of the balance modulator 1 (output a). Sketch the spectrum and label the frequencies. [2] • Sketch the spectrum at the output b and output c. Label the frequencies. [3]

  15. Example The SSB Receiver has output at 1 kHz. The carrier used and suppress at the transmitter was 2 MHz, and the upper sideband was utilized. Determine the exact frequency at all stages for a 455 kHz IF frequency.

  16. Example 1. At 100% modulation, an AM signal has a total power of 1200 watts. If it was converted to SSBSC and the sideband component had the same amplitude as before, the total power would be: a. 100 watts. b. 200 watts. c. 400 watts. d 800 watts. 2. The output of a balanced modulator in an SSB transmitter being modulated with a modulating signal is: a. conventional AM. b. SSB. c. DSB-SC. d. a sinewave at the carrier frequency

  17. Example Figure 1  3. In Figure 2, the output signal of stage (d) is: a. an AM signal with a carrier frequency of 490 kHz. b. an AM signal with a carrier frequency of 1360 kHz. c. a 490 kHz sinewave. d. a 1 kHz sinewave.

  18. Example Figure 2 : SSB Transmitter 4. In Figure 2, the ouput signal of stage (d) is: a. DSB-SC at 500 kHz. b. DSB-SC at 10 MHz. c. SSB at 500 kHz. d. SSB at 10 MHz.

More Related