1 / 18

K. Anderson, A. Gupta, J. Pilcher, H.Sanders, F. Tang, R. Teuscher, H. Wu

Introduction Interface Design Performance and Radiation Test Results Production Quality Control Conclusions. ATLAS Tile Calorimeter Interface The 8 th Workshop on Electronics for LHC Experiments, Colmar, 9-13 September 2002. K. Anderson, A. Gupta, J. Pilcher, H.Sanders,

afya
Download Presentation

K. Anderson, A. Gupta, J. Pilcher, H.Sanders, F. Tang, R. Teuscher, H. Wu

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Introduction Interface Design Performance and Radiation Test Results Production Quality Control Conclusions ATLAS Tile Calorimeter InterfaceThe 8th Workshop on Electronics for LHC Experiments, Colmar, 9-13 September 2002 K. Anderson, A. Gupta, J. Pilcher, H.Sanders, F. Tang, R. Teuscher, H. Wu The University of Chicago

  2. INTRODUCTION: TileCal and Its Readout Electronics • 64 modules in barrel region • (r1=2.28M r2=4.23M L=5.64M) • 128 modules in extended regions • (r1=2.28M r2=4.23M L= 2.65M) • 256 electronics drawers (64x4) TileCal Interface Interface

  3. INTRODUCTION: TileCal and Its Readout Electronics Each Electronics Drawer Contains Following Electronics Boards: • 45 PMT Blocks in barrel region • 31 PMT Blocks in extended regions • One Front-end Electronics 3-in-1 Card Per PMT Block • PMT High Voltage Boards • 3-in-1 Motherboard (4 sections) • 8 Trigger Summing Cards in barrel region • (Stacked on 3-in-1 Motherboard) • 6 Trigger Summing Cards in extended region. • (Stacked on 3-in-1 Motherboard) • 1 Source Calibration Card • (Stacked on 3-in-1 Motherboard) • 8 Digitizer Boards in barrel region • 6 Digitizer Boards in extended regions • 1 Interface Card • (Stacked on one of Digitizer Boards)

  4. INTRODUCTION: Interface Location in Electronics Drawer • A total of 256 Interface cards needed (One per drawer) • Card dimensions: 189x100mm • Located near center of drawer • Receive TTC optical signals in electronics drawer for functional and timing controls • Convert to LVDS signals and distribute to 8 digitizer boards and 3-in-1 mother board • Transfer event data from digitizer boards to RODs • Input from 8 Digitizer Boards (from 16 Tile-DMU chips) • Output to off-detector ROD modules via G-link

  5. INTERFACE DESIGN: Goals Goals: • Complete 2-fold redundancy to ROD. (except for LVDS receivers) • Avoid single point of failure for data from full drawer • Output data robust against transient SEE errors on link • TTC failure detection and automatic switch function • Interface automatic selects a TTC signal based on signal failure conditions

  6. INTERFACE DESIGN: Goals (Cont.1) Goals: • Data Organizer • Collect data from 16 Tile-DMUs in parallel based on Tile-DMU output protocol • Repack 32-bit data words from scrambled data transferred over 2-bit LVDS data lines (40Mpbs) • Insensitive to timing differences related to digitizer board geometry • CRC-16 and Global CRC transmission error checks over input and output segments Altera EP20K160E

  7. INTERFACE DESIGN: Goals (Cont.2) Goals: • Data Organizer • G-link protocol control logic. • 640Mbps output data rate (371Mbps required for TileCal @ 100Khz LVL1A rate) • Low Cost FPGA designs • Altera EP20K200E • On-board JTAG configuration port • Single 3.3V Power Supply Altera EP20K160E

  8. INTERFACE DESIGN: TTC Receiver TTC Receiver Output Waveforms

  9. INTERFACE DESIGN:Structure of Data Organizer

  10. INTERFACE DESIGN: Tile-DMU data stream format

  11. INTERFACE DESIGN: Tile-DMU data stream format

  12. INTERFACE DESIGN: Repacked stream data format

  13. INTERFACE DESIGN:G-link Optical Transmitter(Taiwan) max3288cue From G-link Serializer VCSEL Diode Serializer Output Waveforms

  14. TEST RESULTS: System Readout Performance • Muon response for the 3 sampling depths (q=90o) • Pedestal Superimposed • Using “signal” from empty events • Width reflects energy algorithm as well as electronics • 10 digitizations for each measurement (not optimized) • Muon signal well resolved from pedestal

  15. TEST RESULTS:Radiation Requirements • Interface located at z=160cm r=410cm

  16. TEST RESULTS:Radiation Tests • Interface located at z=160cm r=410cm • All 3 studies showed Interface was fully operational under tests

  17. Production Quality Control • Web Materials • Schematics, specification drawings, gerber, QC requirements, revision history etc. • Instructions to vendor (PCB and assembly) • Parts, artwork files provided by Chicago, vendor responsible for PCB fabrication and assembly • 5 trial boards based on full production setup • Burn-in test (power-up @65C for one week) • All functional and performance tests • Record to Database (Web accessible) • Others

  18. Conclusions • Design is well suited to our needs • Performance and Radiation tests demonstrated well satisfactory • Mass production is being installed in TileCal

More Related