1 / 17

Backgrounds for HAPPEx

Backgrounds for HAPPEx. Ryan Snyder April 7, 2006. Contributions to Background. 1. Quasielastic fraction 2. Aluminum end caps of target cells 3. Rescattering 4. Poletip -- Bob Michaels. Sliding Momentum Cut. Compare E_meas to E_calc: E_calc = energy of elastically scattered electron

Download Presentation

Backgrounds for HAPPEx

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Backgrounds for HAPPEx Ryan Snyder April 7, 2006

  2. Contributions to Background 1. Quasielastic fraction 2. Aluminum end caps of target cells 3. Rescattering 4. Poletip -- Bob Michaels

  3. Sliding Momentum Cut Compare E_meas to E_calc: E_calc = energy of elastically scattered electron E_meas = P_o + dp (in MeV) Numbers don’t compare directly due to precision of spectrometer angles and calibration of spectrometer Thus, a Delta offset is used to move the difference between calculated and measured energies to zero So, a cut is applied on (P_o + dp + Delta) - E_calc < -15 MeV

  4. Run # LDelta RDelta Beam Current(uA) 2271 -0.06 3.51 0.52366 2366 -2.24 0.02 0.392367 2367 -2.96 0.44 0.662509 2509 -1.63 0.62 0.582689 2689 -1.46 0.68 0.622690 2690 -1.7 0.31 0.6122780 2780 -0.25 3.29 0.282781 2781 -0.09 3.22 0.6

  5. With -15 MeV cut, averages work out to be Left Arm = 0.206 % Right Arm = 0.401% Both = 0.303 % % quasielastic = 0.15 +/- 0.15 % A_qe_He = -2ppm (+/- 50%) Overall correction ~ 11 ppb

  6. Aluminum Background - He Integrating mode: He production run: L-arm = det1/bcm1 = 3.556 R-arm = det1/bcm1 = 3.558 Al dummy target run: L-arm = 0.222 R-arm = 0.234 Using “xt” factor of 0.278, get background fractions L-arm = 1.74% R-arm = 1.83% Bkgrnd_Al = 1.8 +/- 0.18% Total Correction = 39 ppb

  7. Aluminum Background - H “xt” factor of 0.125 Integrating Mode: Det1 = 0.64% Det2 = 0.72% Det3 = 0.60% Det4 = 0.79% Total = 0.7% Front window is thicker than back window so this will be a bit higher, but no more than 50%

  8. Rescattering From positive dp scan, get relative rates From negative dp scan, get fraction relative to elastic peak Then, from each section of inelastic spectrum, do (Fraction relative to elastic) x (Relative rate) = Rescattering percentage Add each section up to calculate total rescattering fraction

  9. Helium

  10. Rescatter fraction = 0.45 + 0.44 + 0.027 = 0.92%

  11. Rescat_He = 0.25 +/- 0.15 % A_qe_rescat = -2 +/- 3 ppm Total Correction = 13 ppb

  12. Hydrogen

  13. Rescatter = 0.07 + 0.03 ~0.1% A_Delta = 10 +/- 5 ppm

More Related