1 / 27

Configuring Routers

Configuring Routers. I’ve got to program a router! . What do I have to do. Log on to the router. Router> Router>enable Router# Router#config t. Config t is the place to be!. Name the router!. Step One. Router(config)#hostname Lab-A. Lab-A.

trina
Download Presentation

Configuring Routers

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Configuring Routers

  2. I’ve got to program a router! What do I have to do

  3. Log on to the router Router> Router>enable Router# Router#config t Config t is the place to be!

  4. Name the router! Step One Router(config)#hostname Lab-A Lab-A

  5. Password protect the Privilege Mode Step Two Lab-A(config)#enable secret class Commands Password Results in: enable secret 5 $1$emBK$WxqLahy7YOAf0nifub

  6. Configure the Interfaces Step Three Lab-A(config)#interface serial0 Lab-A(config-if)# (Note prompt change)

  7. Address the Interface(S0) Lab-A(config-if)#ip address 201.100.11.1 255.255.255.0 Ip address Subnet mask S0=201.100.11.1

  8. Clock ticks MUST be set between routers on the interface with the serial cable DCE end. Serial0 is where the DCE connects in our lab.

  9. We use Serial0 • Lab-A(config-if)#clock rate 56000

  10. Address the next Interface (E0) Lab-A(config-if)#interface ethernet0 (This changes to program interface e0) Lab-A(config-if)#ip address 192.5.5.1 255.255.255.0 E0=192.5.5.1 S0=201.100.11.1

  11. Control z Lab-A# Lab-A#show running-config

  12. Like people, routers have to talk to one another!

  13. Like people, routers have to talk to one another! Step Four Set up routing protocols

  14. Routing Protocols: RIP RIPv2 IGRP EIGRP OSPF

  15. Set up the routing protocol Lab-A(config)#router rip Lab-A(config-router)# version 2 Lab-A(config-router)#network 192.5.5.0 Lab-A(config-router)#network 201.100.11.0 (Note prompt change)

  16. Note! • You have to configure for EACH network • (remember network # is the “wire” #) • Each network is on a separate line • Hit Control z to activate and return to: • Lab-A#

  17. Control Access Control and secure access from: CONSOLE VTY (telnet) AUX (modem)

  18. Control Access Step Five Lab-A(config)#line console 0 Lab-A(config-line)#password cisco (Note prompt change) Lab-A(config-line)#login

  19. Continue Lab-A(config)#line vty 0 4 Lab-A(config-line)#password cisco Lab-A(config-line)#login

  20. Want to save time and move fast between routers? Step Six

  21. Create a host file Lab-A(config)#ip host Lab-A 192.5.5.1 205.7.5.1 201.100.11.1 Lab-A(config)#ip host Lab-B 219.17.100.1 199.6.13.1 201.100.11.2 Lab-A(config)#ip host Lab-C 223.8.151.1 204.204.7.1 199.6.13.2 Lab-A(config)#ip host Lab-D 210.93.105.1 204.204.7.2 Lab-A(config)#control z

  22. Turn on the interfaces: Step Seven • Lab-A(config)#interface s0 • Lab-A(config-if)#no shutdown • Lab-A(config-if)#interface e0 • Lab-A(config-if)#no shutdown

  23. Check and save your configuration (Step 8) • Router#show run (Check) • Router#copy run start (Save)

  24. Let’s Review: • Step 1 – name router • Hostname xxxxx • Step 2 – set “privilege” password and encode it • Enable secret xxxxx • Step 3 – configure interfaces • Interface sX (or eX)

  25. Let us review • Step 4 – Set the routing protocols • Router rip • Step 5 – Set who and where access comes from • Line console (vty) • Step 6 – Create a host file • Ip host xxx.xxx.xxx yyy.yyy.yyy • Step 7 – Turn on interfaces • Router(config-if)#no shutdown

  26. Step 8:Check and Save your work! • Check your config • Router#show run • Save your configuration from RAM to NVRAM • Router#copy run start

  27. You’re Through!

More Related