1 / 29

Objective

Objective. Discuss Expansion Valves and Refrigerants Heat Exchangers Learn about different types Define Heat Exchanger Effectiveness ( ε ). AEV. Maintains constant evaporator pressure by increasing flow as load decreases. Thermostatic Expansion Valve (TXV).

pmarion
Download Presentation

Objective

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Objective • Discuss Expansion Valves and Refrigerants • Heat Exchangers • Learn about different types • Define Heat Exchanger Effectiveness (ε)

  2. AEV • Maintains constant evaporator pressure by increasing flow as load decreases

  3. Thermostatic Expansion Valve (TXV) • Variable refrigerant flow to maintain desired superheat

  4. Refrigerants

  5. What are desirable properties of refrigerants? • Pressure and boiling point • Critical temperature • Latent heat of vaporization • Heat transfer properties • Viscosity • Stability

  6. In Addition…. • Toxicity • Flammability • Ozone-depletion • Greenhouse potential • Cost • Leak detection • Oil solubility • Water solubility

  7. Refrigerants • What does R-12 mean? • ASHRAE classifications • From right to left ← • # fluorine atoms • # hydrogen atoms +1 • # C atoms – 1 (omit if zero) • # C=C double bonds (omit if zero) • B at end means bromine instead of chlorine • a or b at end means different isomer

  8. Heat exchangers Air-liquid Tube heat exchanger Air-air Plate heat exchanger

  9. Some Heat Exchanger Facts • All of the energy that leaves the hot fluid enters the cold fluid • If a heat exchanger surface is not below the dew point of the air, you will not get any dehumidification • Water takes time to drain off of the coil • Heat exchanger effectivness varies greatly

  10. Example: What is the saving with the residential heat recovery system? Outdoor Air 32ºF 72ºF 72ºF Combustion products 52ºF Furnace Exhaust Fresh Air Gas For ε=0.5 and if mass flow rate for outdoor and exhaust air are the same 50% of heating energy for ventilation is recovered! For ε=1 → free ventilation! (or maybe not)

  11. Heat Exchanger Effectivness (ε) C=mcp Mass flow rate Specific capacity of fluid THin TCout THout TCin Location B Location A

  12. Air-Liquid Heat Exchangers Coil Extended Surfaces Compact Heat Exchangers • Fins added to refrigerant tubes • Important parameters for heat exchange?

  13. What about compact heat exchangers? • Geometry is very complex • Assume flat circular-plate fin

  14. Overall Heat Transfer Q = U0A0Δtm Overall Heat Transfer Coefficient Mean temperature difference

  15. Heat Exchangers • Parallel flow • Counterflow • Crossflow Ref: Incropera & Dewitt (2002)

  16. Heat Exchanger Analysis - Δtm

  17. Heat Exchanger Analysis - Δtm Counterflow For parallel flow is the same or

  18. Counterflow Heat Exchangers Important parameters:

  19. What about crossflow heat exchangers? Δtm= F·Δtm,cf Correction factor Δt for counterflow Derivation of F is in the book: ………

  20. Example: Calculate Δtm for the residential heat recovery system if : mcp,hot= 0.8· mc p,cold th,i=72 ºF, tc,i=32 ºF For ε = 0.5 → th,o=52 ºF, th,i=48 ºF → R=1.25, P=0.4 → F=0.89 Δtm,cf=(20-16)/ln(20/16)=17.9 ºF,Δtm=17.9 ·0.89=15.9 ºF

  21. Overall Heat Transfer Q = U0A0Δtm Need to find this

  22. Heat Transfer tP,o From the pipe and fins we will find t tF,m

  23. Resistance model • Q = U0A0Δtm • Often neglect conduction through tube walls • Often add fouling coefficients

  24. Heat exchanger performance (Book section 11.3) • NTU – absolute sizing (# of transfer units) • ε – relative sizing (effectiveness)

  25. Fin Efficiency • Assume entire fin is at fin base temperature • Maximum possible heat transfer • Perfect fin • Efficiency is ratio of actual heat transfer to perfect case • Non-dimensional parameter

  26. Summary • Calculate efficiency of extended surface • Add thermal resistances in series • If you know temperatures • Calculate R and P to get F, ε, NTU • Might be iterative • If you know ε, NTU • Calculate R,P and get F, temps

More Related