1 / 5

Underground CSC Synchronization

Underground CSC Synchronization. Would like to be able to synchronize the trigger and DAQ paths of the CSCs to the order of ~1 bx without… cosmic rays LHC beam Pulse CSC teststrips to induce signals on both wires and strips

pillan
Download Presentation

Underground CSC Synchronization

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Underground CSC Synchronization • Would like to be able to synchronize the trigger and DAQ paths of the CSCs to the order of ~1 bx without… • cosmic rays • LHC beam • Pulse CSC teststrips to induce signals on both wires and strips • Mask off comparator distrip=0 or distrip=39, depending on routing of teststrip (probably just easier to always mask these off) • (currently) Trigger on “ADB SYNC” command from CCB • Stripmask = 0x3f (all 6 layers enabled) • Trigger invert = 0 G. Rakness (UCLA)

  2. CLCT distrip occupation with teststrip pulsing • Mask on single distrip per layer (straight-line track) • Pulse • Read CLCT0 key ½-strip • Move to next distrip • Repeat for all distrips 100 times amplitude = 20 di-strip CLCT0 -------- ----- 0 0 1 2 2 88 3 99 4 11 5 17 6 8 7 100 8 0 amplitude = 50 di-strip CLCT0 -------- ----- 0 0 1 100 2 99 3 55 4 4 5 13 6 13 7 100 8 0 amplitude = 5 di-strip CLCT0 -------- ----- 0 0 1 0 2 76 3 0 4 0 5 0 6 0 7 98 8 0 ALCT: LCT sent to TMB 0 CLCT: Pretrigger 341 CLCT: Invalid pattern after drift 147 CLCT: TMB matching rejected event 194 TMB: CLCT,ALCT,or both trigger 0 L1A: L1A received 3900 • CLCT more sensitive than ALCT to teststrip pulsing • di-strip 7 is very sensitive (should be masked off?) • CLCT fully firing by amplitude = 20 G. Rakness (UCLA)

  3. Timing of ALCT in CLCT match window • Example relative ALCT-CLCT timing measurement from chamber in building 904, using: • clct_pretrig_thresh = 2 • clct_pattern_thresh = 4 • CCB in FPGA mode for: • ADB_SYNC • L1A Pulse amplitude = 25.0 Pulse teststrip 1000 times on signal ADB_SYNC ALCT in CLCT match window[0] = 0 ALCT in CLCT match window[1] = 0 ALCT in CLCT match window[2] = 561 ALCT in CLCT match window[3] = 439 ALCT in CLCT match window[4] = 0 ALCT in CLCT match window[5] = 0 ALCT in CLCT match window[6] = 0 ALCT in CLCT match window average = 2.4 ALCT: LCT sent to TMB 1562 CLCT: Pretrigger 1100 CLCT: Invalid pattern after drift 52 CLCT: TMB matching rejected event 48 TMB: CLCT,ALCT,or both trigger 1000 L1A: L1A received 2000 L1A: TMB triggered, TMB in L1A window 1000 G. Rakness (UCLA)

  4. Timing of ALCT in CLCT match window • With teststrip pulsing, the CLCT-ALCT relative timing is measured to be within ~1 bx of the relative timing measured with cosmic rays • should be able to use this technique underground to get approximate timing for full trigger and DAQ paths to sufficient accuracy for large windows • ALCT arrives later (or, CLCT arrives earlier), with… • increasing match_trig_alct_delay (alct_delay)  expected • decreasing time of comparison (after passing threshold)  expected • decreasing CLCT drift delay  expected • decreasing testpulse amplitude  ? • No dependence of relative timing on… • number of layers required for pretrigger  expected, since no drift involved • layer or normal pattern finding algorithm  expected,although still not clear why difference between algorithms is seen with cosmic rays… • No matches seen with inverted pulse • operator error since ALCTs and CLCTs were seen in TMB counters? G. Rakness (UCLA)

  5. To do: • Synchronizing CSC by pulsing • Need to send “ADB Async” through the Local Trigger Control (LTC) module • Will take development • Need to make button to enable software pulsing • Easy • All other software “should” work as well as they do for (independent) cosmic rays • Will see… • update CMS software with: • VME registers with respect to latest TMB firmware updates • broadcast ALCT firmware  broadcast TMB firmware now disabled • Request to resurrect ALCT “Fast self-test” (?) • Write talk for TWEPP-07 G. Rakness (UCLA)

More Related