1 / 60

FCQ321 Series training April 200 8

FCQ321 Series training April 200 8. System Cooking Business Team. Contents. Agenda. General Specification Features and functions Specification Accessories Hardware Wiring diagram Schematic Parts Components Disassembly Trouble Shooting Trouble shooting flow Error message

mahon
Download Presentation

FCQ321 Series training April 200 8

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. FCQ321Series training April 2008 System Cooking Business Team

  2. Contents Agenda • General Specification • Features and functions • Specification • Accessories • Hardware • Wiring diagram • Schematic • Parts Components • Disassembly • Trouble Shooting • Trouble shooting flow • Error message • Error Trouble shooting • Reference

  3. General Specification New Appearance Design • Family looking • Biggest Capacity • Self clean and Steam clean • Dial control • Different pot size Burner

  4. Features & Accessories Oven Features ★ WHAT’S INCLUDED WITH YOUR RANGE

  5. Functions Control Panel - Oven

  6. Control Panel - Surface cooking

  7. Specification

  8. Specification

  9. Specification

  10. Wiring Diagram File

  11. Schematic File

  12. Schematic

  13. Schematic

  14. Disassembly COVER-BACK GUARD WIRE, COVER-BACK MAIN WIRE AND PCB-MAIN 1> Turn off the electrical supply going to the range. 2>Pull the range away from the wall so that you can access the rear panel. 3> Remove Cover-Back Main Wire and Cover-Back Guard Wire 4> Remove screws of PCB assembly and separate PCB assembly. ( When you check PCB, check the proper PCB in default mode and check main PCB.)

  15. Disassembly REGULATOR-ENERGY 1> Turn off the electrical supply going to the range. 2> Pull the range away from the wall so that you can access the rear panel. 3> Remove Cover-Back Guard Wire 4> Remove Regulator-Energy connectors which be replaced

  16. Disassembly REGULATOR-ENERGY 4> Pull out the Knob-Dial. 5> Remove 2 screws and replace Regulator-Energy.

  17. Disassembly HEATER-RADIANT CERAMIC GLASS COOKTOP REMOVAL 1> Unplug the cord or disconnect power 2> Open oven door and remove the 3 screws located at the front of the cook-top, then close the door. 3 Screws 3> Slightly lift up and pull up the cook-top and then unplug the 2 connectors wire at the back by squeezing side tabs and unscrew ground wire.

  18. Disassembly HEATER-RADIANT 4> Protect the cooktop surface and turn the assembly over. 5> To remove the surface elements a) Remove the wires from the element and limiter terminals. b) Remove the element bracket screw (shown below) for the element you are servicing. c) Carefully lift the bottom of the bracket just far enough to remove the element. d) Use sharp tool to remove the heating element REASSEMBLY NOTE: When you reinstall the element make sure that the wires are inserted into the correct tap then reinstall the bracket screw to secure it to the cooktop.

  19. Disassembly LATCH-DOOR AND SWICH-DOOR PLUNGER 1> Turn off the electrical supply going to the range. 2> Open the oven door. 3> Raise the cooktop 4> Remove the cooktop To remove the door latch: a) Remove two screws from the front of cavity. b) Remove a screw from Cover-Back Guard and remove latch-door.

  20. Disassembly LATCH-DOOR AND SWICH-DOOR PLUNGER

  21. Disassembly HEATER-BROIL

  22. Disassembly HEATER-BAKE

  23. Disassembly Lamp To replace bulb and bulb cover: 1> Disconnect power. 2> Remove oven door. 3> Turn the glass bulb cover in the back of the oven counterclockwise to remove. 4> Turn bulb counterclockwise to remove from socket. 5> Replace bulb and bulb cover by turning clockwise. To replace socket assembly: 6> Disconnect the wires from the socket terminals. 7> Use a screwdriver and bend the clips on the socket away from the edges of the liner hole(there are 6 clips on th e socket), and pull the socket out of the liner. Push the socket out from the back of the unit.

  24. Disassembly TEMPERATURE SENSOR

  25. Disassembly STORAGE DRAWER

  26. Disassembly OVEN DOOR To remove the door: 1> Fully open the door. 2> Pull the hinge locks downward (Fig.1) 3> Firmly grasp both sides of the door at the top. 4> Close door to the door removal position, which is approximately 5 degrees. (refer to the Fig.2) Lift door up and out until the hinge arm is clear.

  27. Disassembly OVEN DOOR To replace the door: 1. Firmly grasp both sides of the door at the top position. 2. With the door at the same angle as the removal position, seat the indentation of the hinge arm into the bottom edge of the hinge slot. The notch in the hinge arm must be fully seated into the bottom of the slot. 3. Fully open the door. If the door will not fully open, it means that the indentation is not seated correctly in the bottom edge of the slot. Push the hinge locks up to the locked position. 4. Close the oven door.

  28. Disassembly HANDLE-DOOR AND GLASS-INNER 1> Remove the oven door from the range. 2> Place the oven door on a padded work surface with the front glass facing down. 3> Remove 3 bottom screws from the door. 4> Remove 2 Handle-screws from the door. 5> Lift the door rear assembly off the front assembly and set it aside.

  29. Disassembly HANDLE-DOOR AND GLASS-INNER

  30. Disassembly HANDLE-DOOR AND GLASS-INNER to

  31. Disassembly HANDLE-DOOR AND GLASS-INNER

  32. Disassembly GASKET-DOOR 1> Open the oven door to its fully down position. 2> Pull the ends of the gasket out of the liner holes. 3> Pull the oven door gasket clips out of the holes until all of the clips are removed. REASSEMBLY NOTE: When you install the new gasket, make sure that all of the clips are seated in their liner holes, and that the ends of the gasket are pushed fully into their holes. Use the pointed end of a pencil to push the gasket ends into the holes.

  33. Disassembly PANEL-SIDE 1> Turn off the electrical supply. 2> Remove the oven door from the range 3> Pull the range away from the wall so you can access the back of the unit. 4> Remove the 12 screws from the rear of Panel-Side and remove Cooktop. 5> Remove the (each) 3screws from the top the Panel-Side. 6> Pull the back of the side panel out from the range approximately 10˚(degree) 7> Push forward and remove Panel-Side.

  34. Trouble Shooting Parts Checking Method

  35. Trouble Shooting Parts Checking Method

  36. Trouble Shooting Parts Checking Method

  37. Trouble Shooting Parts Checking Method

  38. Trouble Shooting Parts Checking Method

  39. Trouble Shooting Parts Checking Method

  40. Trouble Shooting

  41. Trouble Shooting

  42. Trouble Shooting Cook-top No heating or Abnormal working

  43. Trouble Shooting

  44. Trouble Shooting

  45. Trouble Shooting

  46. Trouble Shooting

  47. Trouble Shooting

  48. Trouble Shooting

  49. Trouble Shooting

  50. Trouble Shooting

More Related