1 / 30

MuTrFEE Assembly Procedure Mechanical

MuTrFEE Assembly Procedure Mechanical. SUMMARY. Chassis assembly Sub-assemblies of Major component Assembly of FEE cross beams FEE structure assembly ASSEMBLY ORDER CABLE ROUTING Eyebrow installation. FEE NOMENCLATURE. components

jorn
Download Presentation

MuTrFEE Assembly Procedure Mechanical

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. MuTrFEE Assembly Procedure Mechanical may 2000

  2. SUMMARY • Chassis assembly • Sub-assemblies of Major component • Assembly of FEE cross beams • FEE structure assembly • ASSEMBLY ORDER • CABLE ROUTING • Eyebrow installation may 2000

  3. FEE NOMENCLATURE • components • Main Beam: 7”aluminum channels running in Z direction at octant boundaries • Cross beams: 6” Aluminum channels running perpendicular to main beam axis. • Manifold: Inside distribution device for water and air • Spoke: Radial member at sta2 that supports the Main beam • Spoke Tab: Mounting bracket for the spoke located in the piston groove. • Spoke Brace: Member between spokes • Chassis FEE cathode housing • Amp House: FEE anode housing • Amp house mounting beam: channel at detector octant boundary used to mount the Amp House • Main Beam Assembly: 2 main beams joined back to back plus misc hangers. • Cross Beam Assembly: unit comprised of cross beams, chassis, manifolds, HV box, etc • Spider Assembly: spokes and spoke tab at sta2 used to provide radial support to the Main Beams • Spoke assembly: 2 Spokes joined back to back plus misc hangers. may 2000

  4. FEE chassis Cross Beams Main Beams Spoke assembly may 2000

  5. Cathode Chassis assembly • Reference dwg #10Y226395 sheets 1-14 • general description • cold plates, air & water flow path, pcb extraction, electrical isolation , back plane. • Assembly • cold plate, pcb, clamp assembly, chassis‘square-ness’ reqmts, bolt torque, hose fittings, cable holder may 2000

  6. FEE Sub assemblies • Spoke assembly 10Y226391 • consists of 2 spokes, 2 spoke spacers, spoke anchor, bolts • note spacer orientation • install -7 bolts before -6 bolts at spoke anchor • -5 bolts installed from both ends of spacer • torque to values shown may 2000

  7. FEE Sub assemblies • Main Beam Assembly 10Y226391-02 • Main Beam Assy consists of 2 main beams, -4 spacer,-3 mounting bracket, { race hangers, and cable clips not detailed} • mid beam thru holes {sets of 3} used for hangers & clips • use dowel to align holes at spoke attach side. • Rework assy 107223391-04 has specific location may 2000

  8. FEE Sub assemblies • Cross beams assembly 10y226392-01 chassis, manifolds and plumbing. • Manifolds are specific to sta2 or sta3 • Mid manifold is for air • do not route “stuff” across alignment beam path • route hoses to chassis thru cross beam holes • holes on beam flanges not used except if needed for hold-down. may 2000

  9. FEE INSTALLATIONgeneral information • ASSEMBLE PER 10Y226391-01 • Protective covers installed on detectors • For port and octant locations see figure 1 • Start assembly at bottom-then work up. • Review utility of Scaffold • Cables and service connections routed to the racks are attached to cross beam sub- assemblies. may 2000

  10. EYEBROW 3 4 2 Octant number 1 5 8 6 7 Figure 1 Port number may 2000

  11. ASSEMBLY • Cable port to back plate • Spoke assembly to piston • Spoke brace • Mainbeam assembly • Cross Rib assembly sta2 then sta3 • Cable and Hose connections may 2000

  12. 6 cross beams 5 cross beams 1 Cableport Beam Mount 3 Cross brace 4 Main Beams 2 SPOKES may 2000

  13. 6 5 3 1 4 2 7 Remove cross brace may 2000

  14. Assembly philosophy • assembly one type component in all octants, i.e. Install all mainbeams then proceed to crossbeams. [piecemeal] • Positive=frame is protected from misc loads • Positive=easier closure of frame • OR finish all installations at bottom and work around to top, i.e. finish each octant completely before proceeding to next. • Positive=more maneuver room may 2000

  15. CableportMain-Beam Mount Bracket • INSTALL per dwg 10y226390-01 • attach Cableport dwg 10y226391-12 to the back plate • use 3/8-16 x 1 1/8 long socket head bolts • 1/2” dia holes in bracket allow for alignment • do not apply torque to attachment bolts may 2000

  16. Spoke assy to piston • INSTALL per dwg 10y226390-01 • Attach spoke assembly 10Y226391-03 to piston • use 3/8 -16 x 2 1/2 in long bolts • 0.433 Dia bolt holes through anchor allow for alignment • do not torque bolts to spec may 2000

  17. Spoke braces--ASSEMBLY -- • INSTALL per dwg 10y226391-01 • Install spoke braces 10y226391-15 • use 1/4 -20 bolts • braces provide stability to spokes • used as assembly tool only • will be removed may 2000

  18. Mainbeams tospoke and cableport • Install Main Beam Assy per dwg 10y226391-01 • start assy at bottom octant • attach to the beam mount bracket. • Attach to spokes • Rework assy 107223391-04 has specific location. [Voltage bus bar routing] may 2000

  19. Cross ribs • Install sta2 crossribs [stiffens frame] • Install per dwg 10y226391-01 • place beams in a position ‘downstream’ of final bolt on location. • Move beams upstream to align 4 ea 3/8 dia. mounting bolts. • 1/2 inch Slots allow adjustment • engage threads in mainbeams • do not torque bolts • install all octants may 2000

  20. Cross ribs • Sta2 continued: • install all octants • IF CLOSURE PROBLEMS • Adjust {Beat and Bash} components into place • slidecrossbeams up or downstream • Install sta3 cross beams • NOW TIGHTEN ALL BOLTS. may 2000

  21. Main beam mount Main beam assembly Spoke brace Spoke assembly Spoke tab may 2000

  22. CABLING • Starting at bottom [6 o’clock] Octant • route cabling to port location ‘D &F’ • route cabling through holes at ends of crossbeams • contain cables inside the mainbeams using clips to bolt holes in beams • bolt holes provided in side plate of the cableport/mainbeam bkt for cable holddown. • NEED CABLE PROTECTION FROM LAMPSHADE may 2000

  23. CABLING • Detector cabling • limited space 4” at sta2 downstream det. • avoid cabling through alignment beam path • good luck may 2000

  24. eyebrow 3 4 2 1 5 8 6 7 Octant at bottom may 2000

  25. Station 1 • ASSEMBLE PER 10Y226394-01 • assemble in-situ • mount chassis to plate • mount manifold assy to plate may 2000

  26. Installation notes • Using piecemeal assy routine may allow for extended use of scaffolding • Stow cross rib cabling within the beam height • Don’t walk on chassis • May need protection cover plate for crossbeams chassis • holes on flanges of cross beam can be used to mount a plywood shield • crossribs weight is approx 100 pounds • pay attention to bolt torque values • - remove Spoke brace • install HV bus bar: attach guide bracket to cross rib flange holes may 2000

  27. TESTS • WATER /air circulation flow tests • check alignment beam interference may 2000

  28. Hydraulics • Hose and fitting dwg callouts are obsolete due to psi change. • use: Material Nylon 11, 250 psi rating • 1/8” id: hose from Omega #TYNY 14126 • 3/8 id.: hose from Omega #TYNY 12375 • 1/2 id hose :braid reinforced flexible PVC tubing # TYRP 3412 may 2000

  29. Hydraulics • Station 2-3 plumbing per 10y226399-01 • Station 1 plumbing per dwg 10y226399-02 • distribution of air and water inside the magnet from manifold to chassis uses 1/8 id dia hose • water into the magnet uses 3/8 id hose except 1/2” id hose used for delivery to station1 • water flow rate: 0.25gpm/chassis • air flow : 5.2 SCFM may 2000

  30. Hydraulics • Fluid flow is determined by hose and orifice size • water metered by 1/8” id hose • air metered by 0.04 orifice at chassis • water psi at input regulated at 50psig • air psi input at 20psig may 2000

More Related