1 / 18

Work Examples

Work Examples. [1] Sliding Block. Δ x. F. CM. work done to the control mass so it is energy gained. [2] Shear Work on a Fluid. Belt. shear stress × speed × area. v x. W. t. CM. Liquid Bath. work done to the control mass so it is energy gained. Work Examples.

jenn
Download Presentation

Work Examples

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Work Examples [1] Sliding Block Δx F CM work done tothe control mass so it is energy gained [2] Shear Work on a Fluid Belt shear stress × speed × area vx W t CM Liquid Bath work done tothe control mass so it is energy gained

  2. Work Examples [3] Boundary Displacement Gas Expansion W p0 boundary work Δz CM p1 work done by the control mass so it is energy lost Strain (Compression/Expansion) F boundary work (constant area) Δz CM1 work done to the control mass so it is energy gained

  3. Work Examples [4] Shaft/Propeller CM torque × angular speed work done tothe control mass so it is energy gained W [5] Electrical Work (Heat Generation) CM Joule (or resistive or Ohmic) heating R work done tothe control mass so it is energy gained W + - V

  4. Work Examples [6] Surface Tension CM Soap bubble air surface tension × area change straw CM work done tothe control mass so it is energy gained Soap film inside a wire movable wire ΔA

  5. Work Examples [7] Spring Compression F Δx

  6. Enthalpy We can literally define a new specific property enthalpy as the summation of the internal energy and the pressure × volume (flow work) Porter, 1922 Thus for open systems, the first law is frequently written as

  7. Property, State, and Process • Property is a macroscopic characteristic of the system • State is the condition of the system as described by its properties. • Process changes the state of the system by changing the values of its properties • if a state’s properties are not changing then it is at steady state • a system may undergo a series of processes such that its final and initial state are the same (identical properties) – thermodynamic cycle • Phase refers to whether the matter in the system is vapor, liquid, or solid • a single type of matter can co-exist in two phases (water and steam) • two types of matter can co-exist in a single phase (a water/solvent mixture) • Equilibrium state occurs when the system is in complete mechanical, thermal, phase, and chemical equilibrium no changes in observable properties

  8. Properties • extensive properties (dependent on size of system) • U internal energy [kJ] Henthalpy (total energy) [kJ] • V volume [m3] m mass[kg] • S entropy [kJ/K] • intensive properties (independent of size of system) • density [kg/m3] • T temperature [K] • p pressure [Pa] • x quality [-] • specific properties: the values of extensive properties per unit of mass of the system [kg-1] or per unit mole of the system [kmol-1] (inherently intensive properties) • u specific internal energy [kJ/kg] h specific enthalpy [kJ/kg] • v specific volume [m3/kg] • s specific entropy [kJ/(kg-K)]

  9. Pure Substances, Compressible Systems p-v-TRelationship • seek a relationship between pressure, specific volume, and temperature • from experiment it is known that temperature and specific volume are independent • can establish pressure as a function of the others p-v-T surface single phase: all three properties are independent (state fixed by any two) water • two-phase: properties are dependent on each other (state fixed by specific volume and one other) • occurs during phase changes saturation state: state at which phases begins/ends

  10. Pure Substances, Compressible Systems p-v-TSurface Projections phase diagram p-vdiagram • two-phase regions are lines • triple line is a triple point • easily visualize saturation pressure & temperature • constant temperature lines (isotherms)

  11. Pure Substances, Compressible Systems p-v-TSurface Projections T-vdiagram • constant pressure lines (isobars) • quality xdenotes the ratio of vapor to total mass in two-phase mixture two-phase properties from saturation properties

  12. Phase Changes • vaporization/condensation– change from liquid to gas and vice versa • only occurs below critical point • above critical point, the distinction between the two states is not clear • melting/freezing – change from solid to liquid and vice versa • only occurs above triple point • below triple point, the liquid state is not possible and solids change directly to gas (sublimation)

  13. Evaluating Liquid Properties v(T,p) ≈ vf(T) u(T,p) ≈ uf(T) h(T,p) ≈ uf(T)+pvf(T) For liquids, specific volume and specific internal energy are approximately only functions of temperature (saturated liquid) When the specific volume v varies little with temperature, the substance can be considered incompressible it follows incompressible liquids thus Changes in u and h can be found by direct integration of specific heats

  14. Compressibility Factor Compressibility Factor 8.314 kJ/kmol∙K 1.986 Btu/lbmol∙oR 1545 ft∙lbf/lbmol∙oR universal gas constant (molecular weight) At states where the pressure p is small relative to the critical pressure pc (where pR is small), the compressibility factor Z is approximately 1. Virial equations of state:

  15. Evaluating Gas Properties At states where the pressure p is small relative to the critical pressure pc (where pR is small), the compressibility factor Z is approximately 1. ideal gas For ideal gas, specific internal energy and enthalpy are approximately only functions of temperature u(T,p) ≈ u(T) h(T,p) ≈ u(T)+pv= u(T)+RT ≈ h(T) Specific heat and Changes in u and h can be found by direct integration of specific heats

  16. Heat Transfer • Heat Transfer is the transport of thermal energy due to a temperature difference across a medium(s) • mediums: gas, liquid, solid, liquid-gas, solid-gas, solid-liquid, solid-solid, etc. • Thermal Energy is simply the kinetic energy (i.e. motion) of atoms and molecules in the medium(s) • Atoms/molecules in matter occupy different states • translation, rotation, vibration, electronic • the statistics of these individual molecular-level activities will give us the thermal energy which is approximated by temperature • Heat Transfer, Thermal Energy, and Temperature are DIFFERENT. DO NOT confuse them. • Heat generation (electrical, chemical, nuclear, etc.) are not forms of heat transfer Q but forms of work W • Q is the transfer of heat across the boundary of the system due to a temperature difference

  17. Definitions Symbol/Units Quantity Meaning Energy associated with molecular behavior of matter U [J] – extensive property u[J/kg] – intensive property Thermal Energy Means of indirectly assessing the amount of thermal energy stored in matter T[K] or [°C] Temperature Thermal energy transport due to a temperature gradient (difference) Heat Transfer various Thermal energy transferred over a time interval (Δt > 0) Heat Heat Transfer Thermal energy transferred per unit time Heat Rate/Heat Flow Thermal energy transferred per unit time per unit surface area Heat Flux

  18. Modes of Heat Transfer Conduction & convection require a temperature difference across a medium (the interactions of atoms/molecules) Radiation transport can occur across a vacuum

More Related