1 / 77

Model MAV9750AWW - features

Model MAV9750AWW - features. Maytag Atlantis III. Model MAV9750AWW Oversize Capacity Plus Quiet Plus II 6 Speed Select Stainless Steel Tub. Opening Console. T15 Torx. To Access the Console Control Components: Remove the three T15 Torx Screws from the top of the console

jael-warner
Download Presentation

Model MAV9750AWW - features

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Model MAV9750AWW - features Maytag Atlantis III Model MAV9750AWW Oversize Capacity Plus Quiet Plus II 6 Speed Select Stainless Steel Tub

  2. Opening Console T15 Torx To Access the Console Control Components: Remove the three T15 Torx Screws from the top of the console Rotate the top of the console toward the front of the machine and lift

  3. Component Access Wiring diagram On the new Atlantis, the console assembly can be easily removed if necessary

  4. Removing console Disconnect: Lid switch harness 120 volt line cord Console ground wire Main wiring harness Pressure switch hose

  5. New on The Atlantis! Main Harness Disconnects

  6. Lower Cabinet Components Can Be Checked From The Harness

  7. Removing Selector Knobs Black tape on blade to protect from scratching To remove selector knobs, use a plastic putty knife or metal knife(taped) and carefully pry off knob

  8. Removing Timer Cap

  9. Removing Knob Locking tab The knob pulls off the locking tab

  10. Console Control Components Extended Spin Switch Extra Spin Switch ATC Switch Timer & Chime Wash/Spin Speed Finger Faucet Pressure/ Infinite Water Level Switch Chime Volume Switch Wash/Rinse Temperature

  11. Removing The Lid To remove Lid, first remove one of the plastic hinges

  12. Remove Hinge Remove Hinge Pry top of hinge toward center Push up to release Locking Tab

  13. Removing Lid After removing one of the hinges, cock the lid at an angle and slide the remaining hinge pin out of it’s receptacle

  14. Popping The Top 2 ½” Lift Top Insert putty knife to release spring clip. Repeat process on the opposite side

  15. Top Open Detachable Main Wiring Harness Connector Lid Switch Water Valves ATC Thermostats Dispenser Cup Tub Cover Agitator Spring Clips

  16. Removing Front Access Panel Remove 5/16” screw on each side of cabinet Pull top of panel out and lift off bottom clips 1 2 Clip 3 4

  17. Front Panel Removed

  18. Components Warning sticker – use as position reference Outer Tub Suspension springs Drain Hose Tub Hose Transmission Motor Pump

  19. Bottom of the Machine Pump Motor Transmission pulley Roll belt off transmission pulley to remove

  20. Pressure Hose and Dome Pressure Dome

  21. Lid Switch Components Plunger Guide Tube Lid Cam Screw (2) Lid Switch

  22. Lid Switch Assembly Lid Cam Guide Tube Plunger Lid Switch

  23. Water Inlet Assembly Hot Valve Cold Valve ATC Thermostats

  24. Two locking tabs secure the top of the inlet flume to the base Thermostats come as part of an assembly

  25. Parts breakdown Tub Cover Seal Screw (4) Dispenser Cup Agitator Bolt Inner tub Agitator/Auger ASSY Isolator Screw (4) Outer Tub Screw (6) Gasket Tub/Housing Seal Tub Cover

  26. Removing Agitator The Agitator is held to the shaft with a 1/2” bolt Dispenser Cup Agitator ½” Bolt and seal

  27. To remove tub cover, push down on cover while releasing plastic clips and lift off.

  28. Removing Inner Tub Remove four ½” screws

  29. Nylon Seal on screw Nylon Seal Replace if damaged

  30. When reassembling, position top plate on locating tabs Used with stainless basket

  31. Removing inner tub With top plate removed, lift out inner tub

  32. Spring Tool Part # 22002922 Upper Slot – Older Performa and Brand Washers Lower Slot – Atlantis and 1999 Performa Washers

  33. Remove Six Suspension Springs Start in the front and work toward the rear

  34. With belt, hoses and springs detached, roll out the tub assembly

  35. Top “O” Ring Groove Part #25-7941

  36. Seal Nut Side Top Bottom

  37. Seal Nut Removal Seal Nut Tool 22002898 Wrench 35-2968

  38. “O” Ring Seal Nut Basket Hub Tub Seal Housing Assembly Spin Bearing Transmission ASSY

  39. Lower Bearing Tub Support Tub Brace (3) Suspension Housing Screw (6) Brake Spring Retainer Screw (6) Brake Spring HP Plastic Screw (3) Brake Rotor and Lining Snubber 10-24 x .50 Screw (6) Stator brake Thrust Bearing kit Pulley/Dust Cover kit Cam Washer 1.25 ODX Retaining Ring

  40. View of Basket Hub

  41. Seal

  42. Remove four 5/16” screws

  43. Remove six 3/8” screws securing outer tub Take note of the three spring hangers before separating outer tub

  44. Separate outer tub from transmission assembly

  45. Foam Gasket

  46. Rubber Seal

More Related