1 / 7

Rotated Disk Electrode Voltammetry RDEV

Rotated Disk Electrode Voltammetry RDEV. insulator. r 1. w in s -1 , so f in rps revolutions per second. “dead” or diffusion layer. Conductor electrode. Laminar flow occurs up to a point, at too high w , we find that turbulent flow occurs. This is when the value

Download Presentation

Rotated Disk Electrode Voltammetry RDEV

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Rotated Disk Electrode Voltammetry RDEV insulator r1 w in s-1, so f in rps revolutions per second “dead” or diffusion layer Conductor electrode Laminar flow occurs up to a point, at too high w, we find that turbulent flow occurs. This is when the value exceeds the Reynold’s number for that particular fluid with a given kinematic viscosity, n, in cm2 s-1. ~ Re=2x105 (Poise) Look in Table 9.2.1 So, w should be ~ 2 ×105n/r2, but other limitations actually mean w < 1000 s-1 or f 10,000 rpm. On the low w side, must rotate fast enough to establish constant, homogeneous supply of material to electrode surface. w > 10 s-1

  2. If one applies a potential which is that needed to obtain mass-transport limited conditions, then what is i? consider: - hydrodynamics - diffusion Why? O + n e R only O present C 0 x d Real profile Must scan E slowly, n < 100 mV s-1 Recall that d is F(1/w). So, How solve? As we did before except incorporate hydrodynamics. Also: Two Cases: 1. Reversible use q expression (Nernst) 2. Before reach MT limit and - irrev. - quasi-rev. ET rxns.

  3. no iDL effects. Case 1:Levich Equation Know: Know: Levich Layer Levich plot If reaction is D–C, then ilim vs. w1/2 is linear with zero intercept. Also if ET reversible: No dependence of wave shape on w! E1/2 Then plot of Eapp vs. will be straight with slope Case 2A: Totally irreversible; O only But, kf is F(E) , so we denote this kf(E). We call this current iK and it is: This is the Kinetic current. So, at high enough -h, we should get kf ?? NO. Zero

  4. We have no ET effects at -h, Irrev. Rev. for i, so we merely get ilim B-V / No MT ic + - ia MT effects E vs Ref ET effects So, if we could vary E and measure iK, we could get ?? Yes! How? Turns out we have: Koutecký – Levich or Inverse Levich plot So make plot of vs. at a given Eapp. E1 E2 E3 E4(on i lim) Same slopes In each. E1 turbulence Slope is vary Eapp intercept is w-1/2 w-1/2 i iK Levich line E1>E2>E3>E4 (for E>E4) More - w1/2

  5. Case 2B: Quasi – Reversible for O and R MT? Do this on your own. Fnc(E) ET Now we have both kfand kb a function of n. Thus, the Koutecký – Levich plots do not have same slope for various Potentials (h). Problems! Minimize errors by using small potential range near the foot of the wave where i is not changing so drastically.

  6. RRDE dR r1 (R) Ring (D) Disk r3 dD r2 dR = dD r1 disk radius r2 – r1 gap r3 – r2 width of ring The collection Efficiency, N, is defined as It is a Function of electrode geometry but is independent of etc. if R is stable. kchem If R Z occurs, then Nexptl < NtheoandN = F(w).

  7. For RRDE Collection Experiments: 1. ERing is held positive enough so as to oxidize any R. 2. No bulk 3. EDisk is scanned. 4. iDisk is measured. 5. iRing is measured. iD,c O + ne R ERing iD,lim + - EDisk vs. Ref iR,lim R O + ne iR,a Review:

More Related