1 / 28

Manual Film Processing Clifford R. Berry, DVM Adjunct Associate Professor, University of Tennessee

ACVR Artifacts. Manual Film Processing Clifford R. Berry, DVM Adjunct Associate Professor, University of Tennessee Veterinary Specialists Center, Maitland, FL. Manual Film Processing. Manual film processing involves dipping the exposed film into tanks of developer, fixer and wash.

hesper
Download Presentation

Manual Film Processing Clifford R. Berry, DVM Adjunct Associate Professor, University of Tennessee

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. ACVR Artifacts Manual Film Processing Clifford R. Berry, DVM Adjunct Associate Professor, University of Tennessee Veterinary Specialists Center, Maitland, FL

  2. Manual Film Processing • Manual film processing involves dipping the exposed film into tanks of developer, fixer and wash. • The chemical are held in stainless steel tanks. • The water should be running and draining. • Temperature of developer and fixer must be known for adequate development.

  3. Manual film processing Developer Fixer

  4. Developer • Chemical must be stirred before submerging the film into the chemicals or there will be heterogeneous development of the film. • Stirrers should be kept separate.

  5. Developer • Time-Temperature technique. • 680F = 5 minutes. • A mechanical timer with a bell is used to time the duration of development and fixing since the room will be dark

  6. Film Hanging • The films are placed on hangers to hold the films within the tank. • Metal clips poke through the film in order to hold onto the film. • Be sure that films are not touching. • If developing multiple films, beware of safety light fog.

  7. Manual Film Processing • The edges of the film will be punctured by the hanger and can be used to identify manual processed films. • Film corners may be cut. • Seen on all four corners.

  8. Manual Film Processing • The films can be air dried • Dryers are available to speed the process of drying films

  9. Manual film processing • Tanks should be covered when not in use to prevent the developer from oxidizing. • Chemical should be replaced on a regular basis.

  10. Film Too Light • Underdeveloped • Exhausted Chemistry • Underexposed

  11. Manual Film Processing • Exhausted Developer • Developer time has to increase to due oxidized developer and with prolonged contact with the developer chemical all crystals (exposed and unexposed) are reduced results in poor contrast.

  12. Common Artifacts Associated with Film Processing • Low fixer level • The entire film was developed but the top portion was not fixed or cleared.

  13. Chemistry Levels Uneven/Low • Low developer and fixer level • The top of the film was never fixed or developed

  14. Chemistry Levels Uneven/Low • Low developer and • Fixer (higher level than developer) The green strip at the top is the portion of the film not developed or fixed

  15. Development - Kiss Artifact • Cleared emulsion on reflected light. • Matching radiograph to accompany

  16. Fixer - Kiss Artifact • Developed but emulsion not cleared so “milky” or colored appearance (sheen) still present at place where two films where in contact within the fixer.

  17. Emulsion Wrinkle/Peel • Emulsion wet enough that peels away from the film base.

  18. Emulsion Peel

  19. Lack of Wash - Fixer Oxidation • Formation of Silver Sulfide

  20. Debunking Solarization • Solarization - • Process for making copy films by overexposure such that a reversal of optical densities are produced when exposed to light. • Rebromination hypothesis considered likely explanation at this time. • Optical reversal occurs after prolonged exposure of the film so that there is a reversal of the H & D curve. • Correct manual processing artifact = Sabatier Effect

  21. Sabatier Effect • White light exposure of the radiograph while in the developer (manual processing). • Results in the silver grains in the areas that are “white” non-exposed becoming developed to Dmax. The partially developed areas are less affected by the light exposure. • Creates characteristic lines of demarcation called “Mackie lines.”

  22. Sabatier Effect

  23. Incomplete fixation • Colored Film • Pink – on view box • Greenish with reflected light • Due to exhausted fixer, incomplete fixation or insufficient rinsing

  24. Non Stirred Developer

  25. Developer - Specific Gravity Effects • Developer Specific Gravity will cause the “strongest”, non oxidized developer to settle to the bottom of the developer tank.

  26. Sight Development

  27. Cathedral Effect

  28. Film Fog - Safety Light • Manually processed. • Light leak or inappropriate safe light in dark room. • Note the shadow (minus density) created by the film hanger.

More Related