1 / 54

Properties of Wood

Properties of Wood. CE A433 – Spring 2008 T. Bart Quimby, P.E., Ph.D. University of Alaska Anchorage Civil Engineering. Cellular Makeup. Cells are elongated, tube like cells Cell walls are made of cellulose Cells are bound together by lignin.

ghall
Download Presentation

Properties of Wood

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Properties of Wood CE A433 – Spring 2008 T. Bart Quimby, P.E., Ph.D. University of Alaska Anchorage Civil Engineering

  2. Cellular Makeup • Cells are elongated, tube like cells • Cell walls are made of cellulose • Cells are bound together by lignin http://concise.britannica.com/ebc/art-66141/Cross-section-of-a-tree-trunk

  3. Effect of Cell Structure • Since the cells are elongated, the wood has different strength properties when stress is transverse or parallel to the cell longitudinal axis. • Shrinkage properties are also different in each direction.

  4. Grain • Grain runs along the trunk. • Grain size is non uniform Grain Direction

  5. Principle Directions • “With the Grain” = Longitudinal • “Cross Grain” or “Perpendicular to Grain” = Radial or Tangential • Strength and Shrinkage Properties are DIFFERENT IN EACH DIRECTION Radial Tangential Longitudinal http://concise.britannica.com/ebc/art-66141/Cross-section-of-a-tree-trunk

  6. Moisture Content & Shrinkage MC = (moist wt – oven dry wt)/ (oven dry weight) x 100 • Living trees may have MC up to 200%. • Lumber in service has MC less than 20% • The loss of moisture results in wood shrinkage • Shrinkage is most pronounced perpendicular to grain • Moisture is found within the wood cell cavities (free water) and the cell walls (bound water)

  7. More Moisture • Fiber Saturation Point (FSP): The MC where all the free water is lost, leaving only the bound water. There is no shrinkage when the MC is above the FSP • Volume changes take place as the MC varies below the FSP. • Typically, MC continues to decrease after both manufacturing and installation. • Equilibrium Moisture Content (EMC): The in service moisture content • This can vary with occupancy and/or season Manufacture Installation

  8. Shrinkage Example • 5 Story Condo in Juneau, AK • It rained all but 3 days during the 4-5 weeks of framing. • In the first year after construction there was considerable shrinkage

  9. Imperfections in Wood Knots http://www.vermonttimberworks.com/images/shake.jpg

  10. Members Cut from a Log Cross Grain • Perpendicular to grain direction may be either tangential, radial, or a combination of each Cross Grain Cross Grain http://web.utk.edu/~grissino/images/zuni%20doug-fir.jpg

  11. Sawn Lumber Visual Grading • Rules agencies establish grading rules based on observed wood quality • Inspector’s visually grade and mark each piece as it is manufactured

  12. Pressure Treated Wood • Wood is often chemically treated to increase it’s durability • Minimizes decay and mold • Discourages insect infestation • Fire treatments also available • Moist, dark (or nearly dark) locations with minimal air circulation are prime locations for decay and mold • High moisture conditions that are variable are also problematic

  13. Standard Sizes for Sawn Lumber • NDS Supplement Section 3, Table 1B • Nominal Sizes are larger than the actual sizes! • Check out the sizes! Not all are readily available • Some available sizes: • 2x2 to 2x12 • 4x4 to 4x12 • 6x6 to 6x12

  14. Sawn Lumber Size Classifications • See text pg 4.30 • Structural Joists and Plank (SJ&P) • 2 to 4 inches thick • 2 inches and wider • Beams & Stringers (B&S) • 5 inches & thicker • Width > thickness + 2 inches • Posts & Timbers (P&T) • 5 inches & thicker • Width <= thickness + 2 inches

  15. Glue Laminated Timbers • Laminations can be strategically used to make efficient use of the best materials. • Members can be fabricated for particular uses • Larger, Longer, & Curved sections are possible http://www.lamisellbeams.com/images/cover-image/lamisell-image03c-shadow04.jpg

  16. Glulams Designed as Beams • Best material on outer faces • Butt splice in compression zone • Scarf splice in tension region

  17. Glulams Designed as Columns • Materials more uniform • Butt joints can be used throughout

  18. Glulam Standard Sizes • See NDS Supplement Table 1C • Common Widths for Western Species GL • 3.1/8”, 5.1/8”, 6.3/4”, 8.3/4”, 10.3/4” • Common depths: • 6” and larger, in 1.1/2” increments http://www.woodnet.org.uk/wec/images/gluelam2.jpg

  19. The National Design Specification • The “model code” for timber design in the US • The NDS Specification tells us what we can do with timber • The NDS Supplement provides material data for the various types of timber

  20. Basic Design Inequality • As with all structural codes: Req’d Strength < Available Capacity • In the NDS this takes the general form: f < F’ or U <fN • Where: • f = stress caused by internal forces • F’ = adjusted design stress = F * modifiers • F = Reference design stresses • U = the LRFD factored internal force • N = nominal capacity = F’ * (Section Property)

  21. Sawn Lumber Reference Values • NDS Supplement Table 4A

  22. Sawn LumberReference Values • NDS Supplement Table 4D

  23. Glulam Reference Values • NDS Supplement Table 5A

  24. Glulam Reference Values • NDS Supplement Table 5B

  25. Sawn Lumber Design Values • NDS Table 4.3.1

  26. Glulam Design Values • NDS Table 5.3.1

  27. The Modifiers

  28. CM: Wet Service Factor • Applies to all reference values • Applies to both Sawn Lumber and Glulams • Specified in EACH NDS Supplement Reference Value Table • This factor generally reduces strengths for wood that is used in a high moisture environment (EMC > 19%)

  29. Ct: Temperature Factor • Applies to all reference values • Use for timber used in environments with sustained temperatures up to 150 deg F • NDS 4.3.4 for Sawn Lumber & NDS 5.3.4 for Glulams • References NDS Table 2.2.3

  30. CL: Beam Stability Factor • Applies only to bending stress, Fb • Applies to both Sawn Lumber and Glulams • Found in NDS 3.3.3 • This factor accounts for instability in laterally unsupported beams (i.e. lateral torsional buckling) • Glulams: This factor is NOT simultaneously applied with the Volume Factor, CV • More on this factor when we cover beam design

  31. More CL • See NDS Equation 3.3-6 • LTB is a function of both the laterally unbraced (buckling) length AND the variation in the moment diagram. • First check the slenderness ratio • RB must not exceed 50 • Then compute CL • Note that CL is a function of the beam size! • This means that you must know the beam size before computing this factor • When designing, this may lead to iterative computations

  32. CF: Size Factor • Applies to Sawn Lumber Fb, Ft, and Fc bent about the strong axis • Found in NDS 4.3.6 • 4.3.6.1: For SJ&P see NDS Supplement Tables 4A and 4B • 4.3.6.2: For B&S with d > 12”, CF = (12/d)1/9 • 4.3.6.3: For beams of circular cross section • The reference values are normalized to a 12” deep member. This factor accounts for the difference.

  33. Cfu: Flat Use Factor • Applies only to Fb for both Sawn Lumber and Glulams when the member is bent about it’s minor axis. • Found in NDS 4.3.7 and 5.3.7 • For Sawn Lumber, values for Cfu are found in the NDS Supplement Tables 4A, 4B, 4C, and 4F • For Glulams, values for Cfu are found in the NDS Supplement Tables 5A, 5B, 5C, and 5D

  34. Ci: Incising Factor • Applies to all reference values for Sawn Lumber. • Found in NDS 4.3.8 • Accounts for damage to member due to incisions made for chemical pressure treatment.

  35. Cr: Repetitive Use Factor • Applies to Sawn Lumber Fb • Found in NDS 4.3.9 • Read criteria in NDS • Intended to account for the community effort of a repetitive series of bending members such as joists, rafters, studs, etc.

  36. Cp: Column Stability Factor • Applies to Fc for both Sawn Lumber and Glulams • Found in NDS 3.7 via 4.3.10 and 5.3.9 • This factor accounts for column stability as a function of slenderness. • There will be more on this factor when column design is discussed.

  37. CT: Buckling Stiffness Factor • Applies to Emin for Sawn Lumber, which has an impact on Cp • Found in NDS 4.4.2 via 4.3.11 • Only applies to truss top chord members, subject to combined bending and axial compression, and made of 2x4 or smaller sections that meet certain criteria.

  38. Cb: Bearing Area Factor • Applies to Fcp for both Sawn Lumber and Glulams • Found in NDS 3.10.4 via 4.3.12 and 5.3.10 • Accounts for increased strength of bearing areas which are, in part, aided by adjacent wood. • More on this one when we cover beams.

  39. CD: Load Duration Factor • ASD ONLY!!!! • Applies to Fb, Ft, Fv, Fc for both Sawn Lumber and Glulams. Also applies to Frt for Glulams. • Found in NDS 2.3.2 via 4.3.2 and 5.3.2 • The value of CD is based on the actual shortest duration load in the load combination being considered. This has the unfortunate affect of making it very difficult to determine the controlling load combination!

  40. Time Effects on Timber Strength • “Wood has the property of carrying substantially greater maximum loads for short durations than for long durations of loading.” NDS 2.3.2.1

  41. Determining ControllingLoad Case • Consider ASD tensile limit state: Ta/A = ft< F’t = FtCDCMCt for ALL LOAD COMBINATIONS • CD is different for every considered ASCE 7 load combination • This makes it tough to see which Ta to use. • To determine the controlling load case divide both sides by CD (Ta/CD)/A = ft / CD< F’t / CD = FtCMCt • The load combination that gives the largest Ta/CD is the controlling load combination

  42. Example • Consider a column subjected to the loads shown

  43. Structural Elements with Multiple Load Sources • Each source has a different make up • Which ASD LC controls the design of the member? D, Lr, S, L D, L W, E

  44. - Determine CD for each source and each combination. - Pick the controlling CD for the combination and apply to all loads in the combination.

  45. f: Resistance Factor • LRFD Only!!!!! • Applies to all reference values except for E • Found in NDS Appendix N.3.2 via 4.3.15 and 5.3.13

  46. KF: Format Conversion Factor • LRFD Only!!!!! • Applies to all reference values except E • Found in NDS Appendix N.3.1 via 4.3.14 and 5.3.12 • Need to know f to determine KF

  47. KF Table

  48. l: Time Effect Factor • LRFD Only!!!!! • Applies to all reference values except E and Emin. • Found in NDS Appendix N.3.3 via 4.3.16 and 5.3.14 • This is the LRFD equivalent to CD. l accounts for time effects on strength. • l is easier to apply than CD since it’s value is specified by ASCE 7 LRFD load combination instead of by actual shortest duration load • Still need to divide load by l to find controlling cases

  49. The l Table

  50. Example • Consider a column with the loads shown

More Related