1 / 27

Caterpillar Cat M318C WHEELED Excavator (Prefix H2D) Service Repair Manual (H2D00001 and up)

service repair manual

fkuseuidkkmm
Download Presentation

Caterpillar Cat M318C WHEELED Excavator (Prefix H2D) Service Repair Manual (H2D00001 and up)

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Service Repair Manual Models M 318C WHEELEDExcavator

  2. w 1/14(W) Shutdown SIS Previous Screen Product: WHEELED EXCAVATOR Model: M318C WHEELED EXCAVATOR H2D Configuration: M318C Excavator H2D00001-UP (MACHINE) POWERED BY 3056E Engine Disassembly and Assembly M318C and M322C Excavators Machine Systems Media Number -RENR9207-02 Publication Date -01/12/2006 Date Updated -05/12/2006 i01904844 Travel Motor - Disassemble SMCS - 4351-015; 79PC-015 Disassembly Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 138-7575 Link Bracket 2 B 1P-1861 Retaining Ring Pliers 1 C 1U-7600 Slide Hammer Puller Gp 1 D 8H-0663 Bearing Puller Gp 1 E 1P-1857 Retaining Ring Pliers 1 Start By: a. Remove the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Remove". Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior of the components should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform disassembly procedures on a clean work surface. Keep components covered and protected at all times. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/4/6

  3. w 2/14(W) Illustration 1 g00992625 1. Attach Tooling (A) and a suitable lifting device to head assembly (2). 2. Remove bolts (1). 3. Remove housing assembly (2). Illustration 2 g00924957 4. Remove bolts (3). 5. Remove valve (4). Illustration 3 g00924958 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/4/6

  4. w 3/14(W) 6. Remove O-ring seals (5). 7. Remove valve (6). Personal injury can result from parts and/or covers under spring pressure. Spring force will be released when covers are removed. Be prepared to hold spring loaded covers as the bolts are loosened. Illustration 4 g00992626 8. Remove valve (7), plug (8), and the O-ring seal. Illustration 5 g00991751 9. Remove valve (9). 10. Remove spring (10) and spool (11). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/4/6

  5. w 4/14(W) Illustration 6 g00992657 11. Remove plug (12) and the O-ring seal. Illustration 7 g00924963 12. Remove plug (13). Personal injury can result from parts and/or covers under spring pressure. Spring force will be released when covers are removed. Be prepared to hold spring loaded covers as the bolts are loosened. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/4/6

  6. w 5/14(W) Illustration 8 g00991753 13. Remove cover (14). 14. Remove bolts (16). 15. Remove cover (15). Personal injury can result from parts and/or covers under spring pressure. Spring force will be released when covers are removed. Be prepared to hold spring loaded covers as the bolts are loosened. Illustration 9 g00991754 16. Remove spring (17). 17. Remove bushing (18). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/4/6

  7. w 6/14(W) Illustration 10 g00991755 18. Remove O-ring seals (19). 19. Remove O-ring seal (20). Illustration 11 g00991756 20. Use Tooling (E) in order to remove retaining ring (21). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/4/6

  8. w 7/14(W) Illustration 12 g00992661 21. Remove plug (22) and the O-ring seal. Illustration 13 g00695123 Note: Record the distance from the locknut to the end of the screw for installation purposes. Illustration 14 g00991758 22. Remove screw (23) and dowel (24). Illustration 15 g00924973 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/4/6

  9. w 8/14(W) 23. Remove plug (25) and the O-ring seal. Personal injury can result from parts and/or covers under spring pressure. Spring force will be released when covers are removed. Be prepared to hold spring loaded covers as the bolts are loosened. Illustration 16 g00991759 24. Remove bushing (27) and spring (26). Illustration 17 g00924975 25. Remove cap (28). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/4/6

  10. w 9/14(W) Illustration 18 g00991760 26. Remove plug (29) and the O-ring seal. 27. Remove relief valve (30). 28. Repeat Steps 25 through 27 for the opposite side. Illustration 19 g00924978 29. Remove O-ring seals (31), O-ring seal (32), and O-ring seal (33). Illustration 20 g00991762 30. Remove bolt (34), the piston, and the setscrew. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/4/6

  11. w 10/14(W) Illustration 21 g00924980 31. Remove plate (36). 32. Remove pin (35) and spool (37). Illustration 22 g00924981 33. Remove cap (38), the locknut, and the screw. Note: Measure the distance between the nut and the end of the set screw for installation purposes. 34. Remove plug (39) and the O-ring seal. 35. Remove plug (40) and the O-ring seal. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/4/6

  12. w 11/14(W) Illustration 23 g00924982 36. Remove barrel (41) from the piston assembly. 37. Remove O-ring seal (42) from housing (43). Illustration 24 g00924983 38. Remove spring (44) and washer (45) from barrel (41). Illustration 25 g00924984 39. Use Tooling (B) in order to remove retaining ring (46). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/4/6

  13. w 12/14(W) Illustration 26 g00924985 40. Remove shim (47). Illustration 27 g00924987 41. Use Tooling (C) in order to remove seal (48). Illustration 28 g00991763 42. Use a suitable press in order to remove rotor assembly (49). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/4/6

  14. w 13/14(W) Illustration 29 g00991764 43. Remove bolts (50). Illustration 30 g00991765 44. Remove pistons (51), center pin (53), and retainer plate (52). Illustration 31 g00991766 45. Remove rings (54) from pistons (51). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/4/6

  15. w 14/14(W) Illustration 32 g00991767 46. Use Tooling (B) in order to remove retaining ring (55). 47. Remove shim (56). Illustration 33 g00991768 48. Place the rotor assembly in a suitable press. Use Tooling (D) in order to remove shaft (57) from bearing (58), shim (59), and bearing (60). Copyright 1993 - 2020 Caterpillar Inc. Mon Apr 6 22:24:55 UTC+0800 2020 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/4/6

  16. w 1/14(W) Shutdown SIS Previous Screen Product: WHEELED EXCAVATOR Model: M318C WHEELED EXCAVATOR H2D Configuration: M318C Excavator H2D00001-UP (MACHINE) POWERED BY 3056E Engine Disassembly and Assembly M318C and M322C Excavators Machine Systems Media Number -RENR9207-02 Publication Date -01/12/2006 Date Updated -05/12/2006 i01904846 Travel Motor - Assemble SMCS - 4351-016; 79PC-016 Assembly Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 138-7575 Link Bracket 2 B 1P-1861 Retaining Ring Pliers 1 E 1P-1857 Retaining Ring Pliers 1 Note: Cleanliness is an important factor. Before you begin the assembly procedure, the exterior of the components should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform assembly procedures on a clean work surface. Keep components covered and protected at all times. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/4/6

  17. w 2/14(W) Illustration 1 g00992746 1. Raise the temperature of bearing (58) and bearing (60). 2. Lower the temperature of shaft (57). 3. Install bearing (60), shim (59), and bearing (58) onto shaft (57). Illustration 2 g00991767 4. Install shim (56). 5. Use Tooling (B) in order to install retaining ring (55). Illustration 3 g00991766 6. Install rings (54) onto piston (51). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/4/6

  18. w 3/14(W) Illustration 4 g00991765 7. Install pistons (51), center pin (53), and retainer plate (52). Illustration 5 g00991764 8. Install bolts (50). Illustration 6 g00992750 9. Install rotor assembly (49). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/4/6

  19. w 4/14(W) Illustration 7 g00925623 10. Install seal (48). Illustration 8 g00924985 11. Install shim (47). Illustration 9 g00924984 12. Use Tooling (B) in order to install retaining ring (46). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/4/6

  20. w 5/14(W) Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment. Illustration 10 g00924983 13. Install washer (45) and spring (44) into barrel (41). Illustration 11 g00924982 14. Install barrel (41) into the piston assembly. 15. Install O-ring seal (42) into housing (43). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/4/6

  21. w 6/14(W) Illustration 12 g00924981 16. Install plug (40) and the O-ring seal. 17. Install plug (39) and the O-ring seal. 18. Install cap (38), the locknut, and the screw into the original position. Illustration 13 g00924980 19. Install pin (35) and spool (37). 20. Install plate (36). Illustration 14 g00991762 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/4/6

  22. w 7/14(W) 21. Install the piston, the setscrew, and bolt (34). Illustration 15 g00924978 22. Install O-ring seals (31), O-ring seal (32), and O-ring seal (33). Illustration 16 g00991760 23. Install relief valve (30). 24. Install plug (29) and the O-ring seal. Illustration 17 g00924975 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/4/6

  23. w 8/14(W) 25. Install cap (28). 26. Repeat Steps 23 through 25 on the opposite side. Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment. Illustration 18 g00991759 27. Install spring (26) and bushing (27). Illustration 19 g00924973 28. Install plug (25) and the O-ring seal. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/4/6

  24. Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL. NO WAITING NOTE: If there is no response to click on the link above, please download the PDF document first and then click on it.

  25. w 9/14(W) Illustration 20 g00991758 29. Install dowel (24) and screw (23) into the original position. Illustration 21 g00992661 30. Install plug (22) and the O-ring seal. Illustration 22 g00991756 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/4/6

  26. w 10/14(W) 31. Use Tooling (E) in order to install retaining ring (21). Illustration 23 g00991755 32. Install O-ring seal (20). 33. Install O-ring seals (19). Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment. Illustration 24 g00991754 34. Install bushing (18). 35. Install spring (17). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/4/6

  27. w 11/14(W) Illustration 25 g00991753 36. Position cover (15). 37. Install bolts (16). 38. Install cover (14). Illustration 26 g00924963 39. Install plug (13). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe... 2020/4/6

More Related