1 / 42

Low Power Design of CMOS Circuits

Explore power dissipation in CMOS circuits and learn techniques for low power design. Understand the components of power and calculate transition and short-circuit power.

dougl
Download Presentation

Low Power Design of CMOS Circuits

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. ELEC 5270-001/6270-001 Spring 2009Low-Power Design of Electronic CircuitsPower Dissipation of CMOS Circuits Vishwani D. Agrawal James J. Danaher Professor Dept. of Electrical and Computer Engineering Auburn University, Auburn, AL 36849 vagrawal@eng.auburn.edu http://www.eng.auburn.edu/~vagrawal/COURSE/E6270_Spr09/course.html ELEC5270/6270 Spring 09, Lecture 4

  2. nMOS Logic (Inverters) For logic 1 input, continuous static power is dissipated. Pseudo-nMOS Saturated-load nMOS R. C. Jaeger and T. N. Blalock, Microelctronic Circuit Design, Third Edition, McGraw-Hill, 2006, Chapter 6. ELEC5270/6270 Spring 09, Lecture 4

  3. CMOS Logic (Inverter) No static leakage path exists for either 1 or 0 input. F. M. Wanlass and C. T. Sah, “Mamowatt Logic using Field-Effect Metal-Oxide-Semiconductor Triodes,” IEEE International Solid-State Circuits Conference Digest, vol. IV, February 1963, pp. 32-33. ELEC5270/6270 Spring 09, Lecture 4

  4. Components of Power • Dynamic • Signal transitions • Logic activity • Glitches • Short-circuit • Static • Leakage Ptotal = Pdyn + Pstat = Ptran +Psc+ Pstat ELEC5270/6270 Spring 09, Lecture 4

  5. Power of a Transition: Ptran VDD Ron ic(t) vi (t) vo(t) CL R = large Ground ELEC5270/6270 Spring 09, Lecture 4

  6. Charging of a Capacitor R t = 0 v(t) i(t) C V Charge on capacitor, q(t) = C v(t) Current, i(t) = dq(t)/dt = C dv(t)/dt ELEC5270/6270 Spring 09, Lecture 4

  7. i(t) = C dv(t)/dt = [V – v(t)] /R dv(t) V – v(t) ─── = ───── dt RC dv(t) dt ∫───── = ∫ ──── V – v(t) RC - t ln [V – v(t)] = ── + A RC Initial condition, t = 0, v(t) = 0 → A = ln V - t v(t) = V [1 – exp(───)] RC ELEC5270/6270 Spring 09, Lecture 4

  8. - t v(t) = V [1 – exp(── )] RC dv(t) V - t i(t) = C ─── = ── exp(── ) dt R RC ELEC5270/6270 Spring 09, Lecture 4

  9. Total Energy Per Charging Transition from Power Supply ∞∞ V2 - t Etrans = ∫ V i(t) dt = ∫ ── exp(── ) dt 00 R RC = CV2 ELEC5270/6270 Spring 09, Lecture 4

  10. Energy Dissipated per Transition in Resistance ∞ V2∞ -2t R ∫ i2(t) dt = R ── ∫ exp(── ) dt 0 R20 RC 1 = ─ CV2 2 ELEC5270/6270 Spring 09, Lecture 4

  11. Energy Stored in Charged Capacitor ∞ ∞ - t V - t ∫ v(t) i(t) dt = ∫ V [1-exp(── )]─ exp(── ) dt 00 RC R RC 1 = ─ CV2 2 ELEC5270/6270 Spring 09, Lecture 4

  12. Transition Power • Gate output rising transition • Energy dissipated in pMOS transistor = CV2/2 • Energy stored in capacitor = CV2/2 • Gate output falling transition • Energy dissipated in nMOS transistor = CV2/2 • Energy dissipated per transition = CV2/2 • Power dissipation: Ptrans = Etransα fck = α fck CV2/2 α = activity factor ELEC5270/6270 Spring 09, Lecture 4

  13. Components of Power • Dynamic • Signal transitions • Logic activity • Glitches • Short-circuit • Static • Leakage Ptotal = Pdyn+ Pstat = Ptran + Psc+ Pstat ELEC5270/6270 Spring 09, Lecture 4

  14. Short Circuit Power of a Transition: Psc VDD isc(t) vi (t) vo(t) CL Ground ELEC5270/6270 Spring 09, Lecture 4

  15. Short Circuit Current, isc (t) VDD VDD - VTp n-transistor cuts-off Vi (t) Vo(t) Volt VTn p-transistor starts conducting 0 Iscmaxf isc(t) Isc Time (ns) tB tE 1 0 ELEC5270/6270 Spring 09, Lecture 4

  16. Peak Short Circuit Current • Increases with the size (or gain, β) of transistors • Decreases with load capacitance, CL • Largest when CL = 0 • Reference: M. A. Ortega and J. Figueras, “Short Circuit Power Modeling in Submicron CMOS,” PATMOS ’96, Aug. 1996, pp. 147-166. ELEC5270/6270 Spring 09, Lecture 4

  17. Short-Circuit Energy per Transition • Escf =∫tBtE VDD isc(t)dt =(tE – tB) Iscmaxf VDD / 2 • Escf= tf(VDD - |VTp|- VTn) Iscmaxf / 2 • Escr= tr(VDD - |VTp| - VTn) Iscmaxr / 2 • Escf= Escr=0, when VDD= |VTp|+ VTn ELEC5270/6270 Spring 09, Lecture 4

  18. Short-Circuit Energy • Increases with rise and fall times of input • Decreases for larger output load capacitance • Decreases and eventually becomes zero when VDD is scaled down but the threshold voltages are not scaled down ELEC5270/6270 Spring 09, Lecture 4

  19. Short-Circuit Power Calculation • Assume equal rise and fall times • Model input-output capacitive coupling (Miller capacitance) • Use a spice model for transistors • T. Sakurai and A. Newton, “Alpha-power Law MOSFET model and Its Application to a CMOS Inverter,” IEEE J. Solid State Circuits, vol. 25, April 1990, pp. 584-594. ELEC5270/6270 Spring 09, Lecture 4

  20. Short Circuit Power Psc = α fck Esc ELEC5270/6270 Spring 09, Lecture 4

  21. Psc, Rise Time and Capacitance VDD VDD Ron ic(t)+isc(t) vi (t) vo(t) vo(t) CL tr tf R = large vo(t) ─── R↑ Ground ELEC5270/6270 Spring 09, Lecture 4

  22. isc, Rise Time and Capacitance -t VDD[1- exp(─────)] vo(t) R↓(t) C Isc(t) = ──── = ────────────── R↑(t) R↑(t) ELEC5270/6270 Spring 09, Lecture 4

  23. iscmax, Rise Time and Capacitance i Small C Large C vo(t) vo(t) iscmax 1 ──── R↑(t) t tf ELEC5270/6270 Spring 09, Lecture 4

  24. Psc, Rise Times, Capacitance • For given input rise and fall times short circuit power decreases as output capacitance increases. • Short circuit power increases with increase of input rise and fall times. • Short circuit power is reduced if output rise and fall times are smaller than the input rise and fall times. ELEC5270/6270 Spring 09, Lecture 4

  25. Summary: Short-Circuit Power • Short-circuit power is consumed by each transition (increases with input transition time). • Reduction requires that gate output transition should not be faster than the input transition (faster gates can consume more short-circuit power). • Increasing the output load capacitance reduces short-circuit power. • Scaling down of supply voltage with respect to threshold voltages reduces short-circuit power; completely eliminated when VDD ≤ |Vtp| + Vtn . ELEC5270/6270 Spring 09, Lecture 4

  26. Components of Power • Dynamic • Signal transitions • Logic activity • Glitches • Short-circuit • Static • Leakage ELEC5270/6270 Spring 09, Lecture 4

  27. Leakage Power VDD IG Ground Gate R Source Drain n+ n+ Isub IPT ID IGIDL Bulk Si (p) nMOS Transistor ELEC5270/6270 Spring 09, Lecture 4

  28. Leakage Current Components • Subthreshold conduction, Isub • Reverse bias pn junction conduction, ID • Gate induced drain leakage, IGIDL due to tunneling at the gate-drain overlap • Drain source punchthrough, IPT due to short channel and high drain-source voltage • Gate tunneling, IGthrough thin oxide; may become significant with scaling ELEC5270/6270 Spring 09, Lecture 4

  29. Subthreshold Current Isub = μ0 Cox(W/L) Vt2 exp{(VGS –VTH ) / nVt } μ0: carrier surface mobility Cox: gate oxide capacitance per unit area L: channel length W: gate width Vt = kT/q: thermal voltage n: a technology parameter ELEC5270/6270 Spring 09, Lecture 4

  30. IDSfor Short Channel Device Isub= μ0 Cox(W/L)Vt2 exp{(VGS –VTH + ηVDS)/nVt} VDS = drain to source voltage η: a proportionality factor W. Nebel and J. Mermet (Editors), Low Power Design in Deep Submicron Electronics, Springer, 1997, Section 4.1 by J. Figueras, pp. 81-104 ELEC5270/6270 Spring 09, Lecture 4

  31. Increased Subthreshold Leakage Scaled device Ic Log (Drain current) Isub 0 VTH’ VTH Gate voltage ELEC5270/6270 Spring 09, Lecture 4

  32. Summary: Leakage Power • Leakage power as a fraction of the total power increases as clock frequency drops. Turning supply off in unused parts can save power. • For a gate it is a small fraction of the total power; it can be significant for very large circuits. • Scaling down features requires lowering the threshold voltage, which increases leakage power; roughly doubles with each shrinking. • Multiple-threshold devices are used to reduce leakage power. ELEC5270/6270 Spring 09, Lecture 4

  33. Technology Scaling • Scaling down 0.7 micron by factors 2 and 4 leads to 0.35 and 0.17 micron technologies • Constant electric field assumed ELEC5270/6270 Spring 09, Lecture 4

  34. Constant Electric Field Scaling • B. Davari, R. H. Dennard and G. G. Shahidi, “CMOS Scaling for High Performance and Low Power—The Next Ten Years,” Proc. IEEE, April 1995, pp. 595-606. • Other forms of scaling are referred to as constant-voltage and quasi-constant-voltage. ELEC5270/6270 Spring 09, Lecture 4

  35. Bulk nMOSFET Polysilicon Gate Drain W Source n+ n+ L p-type body (bulk) SiO2 Thickness = tox ELEC5270/6270 Spring 09, Lecture 4

  36. Technology Scaling • A scaling factor (S ) reduces device dimensions as 1/S. • Successive generations of technology have used a scaling S = √2, doubling the number of transistors per unit area. This produced 0.25μ, 0.18μ, 0.13μ, 90nm and 65nm technologies, continuing on to 45nm and 30nm. • A 5% gate shrink (S = 1.05) is commonly applied to boost speed as the process matures. N. H. E. Weste and D. Harris, CMOS VLSI Design, Third Edition, Boston: Pearson Addison-Wesley, 2005, Section 4.9.1. ELEC5270/6270 Spring 09, Lecture 4

  37. Constant Electric Field Scaling ELEC5270/6270 Spring 09, Lecture 4

  38. Constant Electric Field Scaling(Cont.) ELEC5270/6270 Spring 09, Lecture 4

  39. Problem: A Design Example • A battery-operated 65nm digital CMOS device is found to consume equal amounts (P ) of dynamic power and leakage power. The short-circuit power is negligible. The energy consumed by a computing task, that takes T seconds, is 2PT. • Compare two power reduction strategies for extending the battery life: • Clock frequency is reduced to half, keeping all other parameters constant. • Supply voltage is reduced to half. This slows the gates down and forces the clock frequency to be lowered to half of its original (full voltage) value. Assume that leakage current is held unchanged by modifying the design of transistors. ELEC5270/6270 Spring 09, Lecture 4

  40. Solution: Strategy A. Clock Frequency Reduction • Reducing the clock frequency will reduce dynamic power to P / 2, keep the static power the same as P, and double the execution time of the task. • Energy consumption for the task will be, Energy = (P / 2 + P ) 2T = 3PT which is greater than the original 2PT. ELEC5270/6270 Spring 09, Lecture 4

  41. Solution: Part B. Supply Voltage Reduction • When the supply voltage and clock frequency are reduced to half their values, dynamic power is reduced to P / 8 and static power to P / 2. The time of task is doubled and the total energy consumption is, Energy = (P / 8 + P / 2) 2T = 5PT / 4 =1.25PT • The voltage reduction strategy reduces energy consumption while a simple frequency reduction consumes more energy. ELEC5270/6270 Spring 09, Lecture 4

  42. Comparing Strategies A and B ELEC5270/6270 Spring 09, Lecture 4

More Related