1 / 9

Infrared (IR) Communication

Infrared (IR) Communication. Microwaves. Visible. X-Rays. Gamma Rays. Radio (RF). Infrared (IR). Ultraviolet. Freq. (Hz). 10 9. 10 12. 10 14. 10 15. 10 17. 10 20. $. FCC. Light Spectrum.

burt
Download Presentation

Infrared (IR) Communication

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Infrared (IR) Communication

  2. Microwaves Visible X-Rays Gamma Rays Radio (RF) Infrared(IR) Ultraviolet Freq. (Hz) 109 1012 1014 1015 1017 1020 $ FCC Light Spectrum • Implementation costs rise significantly around 1-10 GHz. (But one important exception is IR at around 500 THz ; very inexpensive.) • Signals above 100 GHz cannot penetrate walls • Most signals below 300 GHz are regulated by the FCC Introduction

  3. How do you Transmit with IR • No conductor • Signal spreads from origin • Signal strength decreases with distance • Can’t use amplitude • Too much noise from other IR sources (lights, people, etc.) • Can’t use sign (no +/-) • Solution: Modulation • Send pulses of light to represent binary information Introduction

  4. Modulation Schemes • SIR - Serial Infrared • 2400bps to 115,200bps • SIR modem is simple and low-cost • SDLC-based MIR • 576Kbps and 1.152Mbps • guarantees a minimal occurrence rate of light pulses • FIR - Fast Infrared • 4Mbps • power usage constant (always the same) Introduction

  5. SIR - Serial Infrared Modulation • 1.6us (or 3/16 bit interval) pulse of light for each ‘0’ in a standard asynchronous data stream • Inverse of serial RS-232 where signal is held high, then pulled down for zeros • Stream consists of a start bit, N data bits, and 1 stop bit (serial packet) Introduction

  6. SDLC-based MIR • A data stream ‘0’ is coded for by the presence of an optical pulse 1/4 of the bit interval in duration (217ns for 1.152Mbps) • The SDLC protocol, with its zero-insertion bit-stuffing approach, guarantees a minimal occurrence rate of zeroes (and therefore light pulses) in the data stream • This also ensures synchronization between a transmitter and receiver can be maintained throughout a packet Introduction

  7. FIR - Fast Infrared • More Ethernet-like in its framing • a packet is made up of a preamble, start of frame delimiter (SFD) and a data payload. • Utilizes 1:4 Pulse Position Modulation (PPM) • each pair of bits in the data stream are represented by a pulse of light emitted in one of 4 available slot positions which comprise a 4PPM symbol • PPM always requires a pulse for each slot, so power usage is independent of the data Introduction

  8. IR Communication Protocols • To use IR hardware easily, we build up layers of protocol that get us farther away from the implementation each step. • Common Protocols: • Serial IR • IrDA Introduction

  9. Differences between Waves and Wire • Distance/$$$ • Wave transmissions are much more expensive than wire • Speed • Wire is a very simple and highly controllable medium which allows for much higher transfer rates • Limitations • IR: • Line of Sight - IR can not travel through opaque objects, so transceivers must be able to see each other. For many commercial products they must be within 15º of each other. • Signal Power - even though we can not see IR, making the signal too strong can easily blind us • RF: • FCC Regulation • Interference with objects and other RF waves Introduction

More Related