1 / 8

Simulation Methodolgy and Calibration

Simulation Methodolgy and Calibration. Date: 2014-03-14. Authors:. Introduction. Evaluation Methodology document defines multiple simulators MAC systems: With a simplified PHY and detailed MAC PHY system: With a simplified MAC and detailed PHY

bing
Download Presentation

Simulation Methodolgy and Calibration

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Simulation Methodolgy and Calibration Date: 2014-03-14 Authors: Gwen Barriac, et. al. (Qualcomm)

  2. Introduction • Evaluation Methodology document defines multiple simulators • MAC systems: With a simplified PHY and detailed MAC • PHY system: With a simplified MAC and detailed PHY • Integrated [in 1359r1]: With detailed MAC and PHY • PER simulator • The definition of integrated simulator [1359r1] includes • MAC simulation accuracy based on event driven approach, and initial features • PHY abstraction which includes advanced PHY features (MIMO, BF etc…) • The definition of MAC simulator is unclear/TBD • PHY abstraction not well defined and may be too simplistic • “The PHY parameters can be simplified to a SISO configuration running over AWGN - path and penetration loss should be modeled according to the scenario-specific definition.” [1359r0] • “MAC system simulation is an integrated system simulation stripped out of the details of PHY modelling, e.g. a SISO configuration with AWGN - path loss and penetration loss should be modeled according to the scenario-specific definition.” [1359r1] • MAC simulation accuracy same as the integrated simulator [1359r1] • In order to proceed with the calibration, we suggest some clarifications on the MAC/Integrated simulators definitions Gwen Barriac, et. al. (Qualcomm)

  3. Proposals in this presentation • We suggest to merge the definition of MAC and Integrated simulators and e.g. keep the name ‘Integrated’ • Within the Integrated sim, define multiple levels of PHY and MAC features to be the target for development and calibration steps • “Phase I” PHY (SISO, flat channel) • “Phase II” PHY (SISO, multipath channel) • “Phase I” MAC (minimal essential MAC features) • “Phase II” MAC (more advanced MAC features) • The definition of Phases is helpful in identifying common milestones in the development process across companies and facilitates the comparison and calibration across simulators • Define calibration steps according to the defined phases • Define a sequence of tests per each PHY and MAC phase Gwen Barriac, et. al. (Qualcomm)

  4. PHY Abstractions for Integrated Simulator • Phase I: (minimum requirement for Integrated simulator) • SISO channel with propagation modeled by path loss, wall loss and shadowing only (‘narrowband model’) • SINR computed with interference from all the sources • Interference recalculated at each “interference event” (e.g. may be multiple in a MPDU) • SINR to PER Mapping • Map SINR on PER curve for the selected MCS and determine loss probability of each MPDU • PER abstraction: use long term SINR-> PER curves mapping (1x1) • PER curves to be used: according to the channel model indicated by the test scenario (e.g. Channel D) • Phase II: • Phase 1 features, with the following differences: • Fading channel model (w/o doppler) • PER abstraction: Effective SINR vs PER mapping curves (1x1) • See separate presentation [2] • Additional phases TBD • MIMO • BF, … Gwen Barriac, et. al. (Qualcomm)

  5. MAC Features for Integrated Simulator • Phase I: (minimum requirement - to be modeled as per IEEE specs) • Backoff procedure with EDCA • Deferral according to Packet Detection and Energy Detection • All overheads • MAC header, FCS, LLC/SNAP, TCP/IP • A-MPDU aggregation • RTS/CTS • BA • Rate selection TBD • Phase II: Additional features • A-MSDU aggregation, BAR • BF, MU-MIMO • Note: EM document should define the required features and the accuracy of modeling, not the way features are to be coded in the simulator Gwen Barriac, et. al. (Qualcomm)

  6. Initial Calibration Plan • Test for Phase I MAC features : Start with simple MAC calibration tests where PHY abstraction is largely irrelevant • E.g. two nodes at short distance such that PER is negligible. • E.g. Multiple nodes at distances such that collisions will cause packet failure with very high probability • Test for Phase I PHY features • Calibration tests with MAC “disabled”: calibrate the PHY abstraction • MAC “disabled” assumes no deferral and no backoff (reuse-one); • The goal is to calibrate the SINRs. MAC overheads need not be modeled • Test for Phase I PHY and Phase I MAC features combined • Simple Calibration tests with MAC functionalities • Calibration of Simulation Scenarios with Phase I PHY • E.g. run the Residential scenario with default parameters (TBD) • Tests for Phase II MAC features … Tests for Phase II PHY …. Gwen Barriac, et. al. (Qualcomm)

  7. Initial Calibration Plan • Calibration tests scenarios • Define, in SS / EM docs, new simple scenarios to be used per each phase • Define default parameters in each Simulation Scenarios (1-4), to be used for more comprehensive calibration • E.g. see doc XXXX • Metrics for the calibration • PHY: CDF of SINR • MAC: TPUT • Use application layer Tput • Other metrics for debugging • Ex: PER log, event traces, etc. Gwen Barriac, et. al. (Qualcomm)

  8. Conclusions • MAC system simulator is vaguely described in EM • The calibration procedure is undefined • We propose to unify the description of MAC and Integrated simulator and define a phased approach for the development and calibration • See doc 14/387 for related proposed changes in the EM document • See doc 14/355 for related proposed changes in the SS document • We propose a plan for the calibration tests Gwen Barriac, et. al. (Qualcomm)

More Related