1 / 34

Harvesting Waste Energy: Bicycle Power Generation

Harvesting Waste Energy: Bicycle Power Generation. RIT-MSD-I Detailed Design Review Winter/Spring 2011-2012 P 12414. Team Members. Daniel Tobin (ME) Project Manager Amina Purak (ISE) Facilitator Aaron Sieczkarek (ME) Chief Engineer Brenda Lisitano (ME) Zheng ( Flora) Li (EE).

bert
Download Presentation

Harvesting Waste Energy: Bicycle Power Generation

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Harvesting Waste Energy:Bicycle Power Generation RIT-MSD-I Detailed Design Review Winter/Spring 2011-2012 P12414

  2. Team Members • Daniel Tobin (ME) • Project Manager • AminaPurak (ISE) • Facilitator • Aaron Sieczkarek (ME) • Chief Engineer • Brenda Lisitano (ME) • Zheng(Flora) Li (EE) GUIDE: Professor Brownell

  3. Design Review Agenda • P

  4. One Page Project Summary Project Background People in countries with inadequate infrastructure have an unmet need for electricity. A bicycle rotation energy harvesting system is a possible source for creating and storing power. This system could provide the energy required for light, communication, or water treatment by converting kinetic energy to electrical energy for small electronic devices. • Problem Statement • Our goal is to transform kinetic energy within a bicycle into an electric power source intended to charge a cell phone. Our device is expected to be cheap to build, easy to install, maintain and use.

  5. Customer Requirements

  6. Specifications

  7. Assembly

  8. Motor Selection Voltage Output Testing on the MIT device

  9. Motor Selection Voltage Output Testing on the Red Light Dynamo

  10. Motor Selection Voltage Output Testing on the White Light Dynamo

  11. Circuits Overview Circuit Diagram for the MIT Device The MIT device uses a 12 V DC motor, a 6V voltage regulator and a 470uF Capacitor. The circuit diagram is shown above. The function of this circuit is to stabilize the DC output from the DC motor and regulate it to a 6V constant output.

  12. Circuits Overview • The voltage supplied by a USB port is nominally 5V. In practical, the output is between 4.75V and 5.25V. A constant DC output of 5V is needed for the design. Circuit Constant 5V DC output Non-linear oscillating voltage input

  13. Circuits Overview • The testing on excising dynamos and products shows that the output of an AC motor is similar to a sin wave. Assuming that the output from the motor is a sin wave with 12V amplitude, 100Hz frequency, and 0 V offset. The first step is to use a Bridge Rectifier to rectify the output voltage. The output from the rectifier is always positive. The circuit diagram and simulation are shown below. As we can see, there is a voltage drop of . is the diode voltage. The Bridge Rectifier

  14. Circuits Overview • The second step is stabilize the voltage output in a smaller range then it is regulated to 5V constant DC output using a voltage regulator. The circuit diagram and simulations are shown. Capacitor C8 and C9 are used to additionally stabilize the voltage.

  15. Circuits Overview Overall Waveform of the simulations Positive Output in Range 12V AC Positive Output 5V DC AC motor Cellphone

  16. Circuits Overview Additional Zenerdiode Circuit As shown in circuit above, a 10V Zener diode is added. The Zener diode does not affect the function of the circuit. It is used to prevent high voltage input damage the voltage regulator. It is not necessary if the output of the motor is always lower than 25V.

  17. Circuits Overview • At the end, after we get the 5V constant output. The output pins will connect to a standard A-type USB connector. The pin 1 and 4 will be connected to the positive 5V pin and the ground of the circuit. The data transfer pins will also be grounded. • Using the pin out below, all different kinds of USB to cellphone connectors can be made.

  18. Circuits Overview • In the design process, we decided to use a DC motor instead of an AC motor because of the price of the motors. The bridge rectifier is no longer necessary. • Assume the 12V DC motor is used in our design. The output from the motor is approximately 5V DC voltage with ripples. The design shown below is used to regulate the voltage output. Circuit diagram for 12V DC motor

  19. Circuits Overview Simulation of 12V DC motor with 12V motor output with ripples. Simulation of 12V DC motor with 8V motor output with ripples.

  20. Circuits Overview • Assume the waveform below is generated by a person riding for 20s with two stops. • According to the simulation, the output of the circuit maintain at 5V when the motor’s output is between 6V to 12V.

  21. BOM

  22. Selected Parts Specs

  23. Cost/Worth Analysis

  24. Calculations …

  25. Shaft Attachment

  26. Motor Attachment

  27. Box Attachment

  28. RPM Calculation

  29. Risks

  30. Test Plan

  31. Example Test Sheet

  32. Gantt Chart for MSDII

  33. Concerns Next Steps

  34. We Welcome Your Questions & Feedback

More Related