Cfr 29 1926 subpart x stairways and ladders
Download
1 / 43

CFR 29 1926 Subpart X Stairways and Ladders - PowerPoint PPT Presentation


  • 1176 Views
  • Updated On :

CFR 29 1926 Subpart X Stairways and Ladders. 1926.1050 Scope, applications, and definitions, applicable to this subpart 1926.1051 General requirements 1926.1052 Stairways 1926.1053 Ladders. 1926.1054 Reserved 1926.1055 Reserved 1926.1056 Reserved 1926.1057 Reserved 1926.1058 Reserved

Related searches for CFR 29 1926 Subpart X Stairways and Ladders

loader
I am the owner, or an agent authorized to act on behalf of the owner, of the copyrighted work described.
capcha
Download Presentation

PowerPoint Slideshow about 'CFR 29 1926 Subpart X Stairways and Ladders' - Lucy


An Image/Link below is provided (as is) to download presentation

Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author.While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server.


- - - - - - - - - - - - - - - - - - - - - - - - - - E N D - - - - - - - - - - - - - - - - - - - - - - - - - -
Presentation Transcript

Osha regulations 29 cfr part 1926 subpart x stairways and ladders l.jpg

1926.1050 Scope, applications, and definitions, applicable to this subpart

1926.1051 General requirements

1926.1052 Stairways

1926.1053 Ladders

1926.1054 Reserved

1926.1055 Reserved

1926.1056 Reserved

1926.1057 Reserved

1926.1058 Reserved

1926.1059 Reserved

1926.1060 Training

1926 Subpart X - App A - Ladders

OSHA Regulations 29 CFR Part 1926 Subpart X - Stairways and Ladders


Slide3 l.jpg

Inventive way to use a Ladder to this subpart

Bottom Line Don’t Try It


1926 1050 a scope and application l.jpg
1926.1050(a) to this subpartScope and Application

  • This subpart applies to all stairways and ladders used in construction, alteration, repair (including painting and decorating), and demolition workplaces covered under 29 CFR part 1926, and also sets forth, in specified circumstances, when ladders and stairways are required to be provided. Additional requirements for ladders used on or with scaffolds are contained in Subpart L - Scaffolds.



Slide8 l.jpg

1926.1050(b) Definitions to this subpart

"Cleat" means a ladder crosspiece of rectangular cross section placed on edge upon which a person may step while ascending or descending a ladder.

"Double-cleat ladder" means a ladder similar in construction to a single-cleat ladder, but with a center rail to allow simultaneous two-way traffic for employees ascending or descending.


Slide9 l.jpg

1926.1050(b) Definitions to this subpart

"Extension trestle ladder" means a self-supporting portable ladder, adjustable in length consisting of a trestle ladder base and a vertically adjustable extension section, with a suitable means for locking the ladders together.


Slide10 l.jpg

1926.1051(a) Provide a stairway or ladder to this subpart at all personnel points of access where there is a break in elevation of 19 inches

(48 cm) or more, and no ramp, runway, sloped embankment, or personnel hoist is provided.


Slide11 l.jpg

1926.1051a)(2) Provide a double-cleated ladder to this subpartor two or more separate ladders when ladders are the only mean of access or exit from a working area for 25 or more employees, or when a ladder is to serve simultaneous two-way traffic.


Slide12 l.jpg

1926.1052 - Stairways to this subpart

(a)(1) Stairways must have landings of not less than 30 inches (76 cm) in the direction of travel and extend at least 22 inches (56 cm) in width at every 12 feet (3.7 m) or less of vertical rise.


Slide13 l.jpg

1926.1052 - Stairways to this subpart

(a)(2) Install stairs between 30 deg. and 50 deg. from horizontal.

(a)(4) Provide a platform where doors or gates open directly on a stairway; the swing of the door must not reduce the effective width of the platform to less than 20 inches (51 cm).


Slide14 l.jpg

1926.1052(a)(3) Riser height and tread to this subpart

depth must be uniform within each flight of stairs, including any foundation structure used as one or more treads of the stairs. Variations in riser height or tread depth shall not be over 1/4 inch (0.6 cm) in any stairway system.

LANDING

Tread

Rise


Slide15 l.jpg

1926.1052(a)(7) Eliminate slippery conditions to this subpart

on stairways before the stairways are used to reach other levels.


Slide16 l.jpg

1926.1052(c)-Stairrails and handrails to this subpart

  • Equip stairways having four or more risers or rising more than 30 inches (76 cm), whichever is less, with:

  • At least one handrail; and

  • One stairrail system along each unprotected side or edge.


Slide17 l.jpg

1926.1052(c)The height of stairrails to this subpart

must be as follows:

Stairrails installed after March 15, 1991, must be not less than 36 inches (91.5 cm) from the upper surface of the stairrail system to the surface of the tread, in line with the face of the riser at the forward edge of the tread.

Stairrails installed before March 15, 1991, must be not less than 30 inches (76 cm) nor more than 34 inches (86 cm) from the upper surface of the stairrail system to the surface of the tread, in line with the face of the riser at the forward edge of the tread.


Slide18 l.jpg

1926.1052(c)(5) Handrails and the top rails to this subpart of stairrail systems must be capable of withstanding, without failure, a force of at least 200 pounds applied within 2 inches (5 cm) of the top edge, in any downward or outward direction, at any point along the top edge.


Slide19 l.jpg

1926.1052 Stairway Systems to this subpart

(c)(7) When the top edge of a stairrail system also serves as a handrail

(c)(8) Stairrail systems and handrails surface

(c)(9) Handrails must provide an adequate handhold

(c)(10) The ends of stairrail systems and handrails must not be a projection hazard

(c)(11) Handrails not a permanent part of the structure

(c)(12) Unprotected sides and edges of stairway landings


Slide21 l.jpg

GOOD OR BAD? to this subpart


Slide22 l.jpg

1926.1053 Ladders to this subpart


Slide23 l.jpg

1926.1053 Ladders to this subpart

(a)(2) Ladder rungs, cleats, and steps must be parallel, level, and uniformly spaced when the ladder is in position for use.

(a)(3)(i) Rungs, cleats, and steps of portable ladders must be spaced not less than 10 inches (25 cm) apart, nor more than

14 inches (36 cm) apart, as measured between center lines of the rungs, cleats and steps.


Slide24 l.jpg

1926.1053 Ladders rungs to this subpart

(a)(4)(ii) The minimum clear distance between side rails for all portable ladders is 11 1/2 inches (29

cm).

(a)(5) The rungs of individual-rung/step ladders must be shaped such that employees' feet cannot slide off the end of the rungs.

(a)(6)(i) The rungs and steps of fixed metal ladders manufactured after March 15, 1991, must be corrugated,

knurled, dimpled, coated with skid-resistant material, or otherwise treated to minimize slipping.


Slide25 l.jpg

1926.1052(a)(12) Coating of Ladders to this subpart

Wood ladders must not be coated with any opaque covering, except for identification or warning labels which may be placed on one face only of a side rail.


Slide26 l.jpg

1926.1053(b) Use to this subpart

The following requirements apply to the use of all ladders, including job-made ladders, except as otherwise indicated:

1926.1053(b)(1) When portable ladders are used for access to an upper landing surface, the ladder side rails must extend at least 3 feet (.9 m) above the upper landing surface


Slide27 l.jpg

1926.1053(b) Use to this subpart

(b)(2) Maintain ladders free of oil, grease, and other slipping hazards.

(b)(3) Do not load beyond the maximum intended load for which they were built, nor beyond their manufacturer's rated capacity.

(b)(4) Use only for the purpose for which they were designed.

(b)(5)(i) Use non-self-supporting ladders at an angle such that the horizontal distance from the top support to the foot of the ladder is approximately one-quarter of the working length of the ladder (the distance along the ladder between the foot and the top support).


Slide28 l.jpg

1926.1053(b) Use to this subpart

(b)(12) If ladders are used where the employee or the ladder could contact exposed energized electrical equipment, they must have nonconductive siderails, except as provided in 1926.951(c)(1) of this part.

Aluminum

Wood


Slide29 l.jpg

1926.1053(b) Use to this subpart

(b)(13) Do not use the top or top step of a stepladder as a step.

(b)(14) Do not use cross-bracing on the rear section of stepladders for climbing unless the ladders are designed and provided with steps for climbing on both front and rear sections.


Slide30 l.jpg

1926.1053(b) Use to this subpart

(b)(15) Must be inspected by a competent person for visible defects, e.g., broken or missing rungs, cleats,

or steps, broken or split rails, corroded components, or other faulty or defective components.

(b)(17) Withdraw from service until repaired: fixed ladders with structural defects, e.g., broken or missing rungs, cleats, or steps, broken or split rails, or corroded components.

(b)(17)(i) Tag immediately with "Do Not Use" or similar language.

(b)(17)(ii) Mark in a manner that readily identifies it as defective.

Remove from service


Slide31 l.jpg

1926.1053(b) Use to this subpart

(b)(20) Face the ladder when ascending or descending.

(b)(21) Use at least one hand to grasp the ladder when progressing up and/or down the

ladder.

(b)(22) Do not carry any object or load that could cause you to lose balance and fall.


Slide32 l.jpg

Missing rung to this subpart

  • Improper angle

  • No extension


Slide34 l.jpg

Ladders and Stairway Citations to this subpart

Standard #Cited #Insp. Penalty

CFR 29 1926.1051 76 72 $ 32,259

CFR 29 1926.1052 428 305 $ 187,234

CFR 29 1926.1053 498 372 $ 234,475

CFR 29 1926.1060 58 57 $ 10,134

Information Gathered from www.osha.gov Inspections Conducted October 2002 through September 2003.


Slide35 l.jpg

1926.1060 Training to this subpart

(a) Must train each employee using ladders and stairways, as necessary, to recognize hazards related to ladders and stairways, and the procedures to be followed to minimize these hazards.

(a)(1) A competent person must train each employee in the following areas, as applicable:

(a)(1)(i) The nature of fall hazards in the work area;

(a)(1)(ii) The correct procedures for erecting, maintaining, and disassembling the fall protection systems to be used;

(a)(1)(iii) The proper construction, use, placement, and care in handling of all stairways and ladders;

(a)(1)(iv) The maximum intended load-carrying capacities of ladders and

(a)(1)(v) The standards contained in this subpart.

(b) Retrain each employee as necessary to maintain the understanding and knowledge acquired through compliance with this section.


Slide36 l.jpg

More Inventive ways to use a Ladders to this subpart

Bottom Line Don’t Try It


Slide37 l.jpg

More Inventive ways to use a Ladders to this subpart

Bottom Line Don’t Try It


Slide38 l.jpg

More Inventive ways to use a Ladders to this subpart

Bottom Line Don’t Try It


Slide39 l.jpg

More Inventive ways to use a Ladders to this subpart

Bottom Line Don’t Try It


Slide40 l.jpg

More Inventive ways to use a Ladders to this subpart

Bottom Line Don’t Try It


Thank you l.jpg
Thank You to this subpart


Slide42 l.jpg

DISCLAIMER to this subpart

This information has been developed by an OSHA Compliance Assistance Specialist and is intended to assist employers, workers, and others as they strive to improve workplace health and safety. While we attempt to thoroughly address recordkeeping, it is not possible to include discussion of everything necessary to ensure a healthy and safe working environment in a presentation of this nature. Thus, this information must be understood as a tool for addressing workplace hazards, rather than an exhaustive statement of an employer’s legal obligations, which are defined by statute,


Slide43 l.jpg

DISCLAIMER to this subpart

regulations, and standards. Likewise, to the extent that this information references practices or procedures that may enhance health or safety, but which are not required by a statute, regulation, or standard, it cannot, and does not, create additional legal obligations. Finally, over time, OSHA may modify rules and interpretations in light of new technology, information, or circumstances; to keep apprised of such developments, or to review information on a wide range of occupational safety and health topics, you can visit OSHA’s website at www.osha.gov


ad