1 / 7

8xADC AMC board

8xADC AMC board. Tomasz Klonowski T.Klonowski@elka.pw.edu.pl Warsaw University of Technology PERG – ISE 3.12.2007. Requirements. 8xADC (100 MHz) + FPGA for d ata acquisition and processing Form factor: AMC.1 (with PCIExpress), single width

zed
Download Presentation

8xADC AMC board

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. 8xADC AMC board Tomasz Klonowski T.Klonowski@elka.pw.edu.pl Warsaw University of Technology PERG – ISE 3.12.2007

  2. Requirements • 8xADC (100 MHz) + FPGA for data acquisition and processing • Form factor: AMC.1 (with PCIExpress), single width • ADC: 14-16 bit, ~100 MHz sample rate, conversion time 7 maximum clocks • FPGA: Virtex 5 with external memory (2-4 MB, 250 MHz) • 2 EEPROMs for FPGA • 2 different clocks (configurable) for ADC 1-4 and ADC 5-8 • clock distribution stability better than 5 ps • IPMI • additional signals from rear • 8x analog signal 50-100 MHz through signal conditioning connected to ADC • 6x clock up to 100 MHz, LVDS bus, jitter less than 5 ps • 2 of them connected to FPGA and ADC (user can choose clock for ADCs) • 4 clocks connected to FPGA, LVDS bus

  3. AMC connector A+ AMC connector B+ Analog signals 1-8 Data 8 bits PCI Express JTAG I2C Clocks 1-2 uC Atmega 128 inhibit Power supply Interconnector Clocks 3-6 Signal conditioning band-pass filters JTAG Data 8 bits Clock distribution AD9510 AD9513 EEPROM XCF16P ADC 1-4 AD6645 ADC 5-8 AD6645 Hot -swap switch FPGA Virtex5 XC5VLX30T Data 8x16 bits Clocks 1-2 Clocks 3-6 Clock configuration bus Data enable Buffers Interconnector Data 36 bits Data 8x16 bits QDR II SRAM 512K x 36 IDT71P74604 Board with analog and clock distribution components Board with digital and IPMI components Block Diagram

  4. Functional • ADC AD6645 - 14-bit, 80 – 105 MSPS, conversion time 4 maximum clocks, • FPGA - Virtex 5 XC5VLX30T • QDR II SRAM IDT71P74604 18 Mb, 250 MHz • EEPROM XCF16P for FPGA – two configurations • IPMI • Clock distribution AD9510, AD9513 – configured by FPGA • clock distribution stability better than 5 ps • 2 different clocks for ADC 1-4 and ADC 5-8 • clocks configured by FPGA • Buffers – 74LCX574 – for latching data from converters

  5. Interface • 8x analog signal 50-100 MHz through signal conditioning connected to ADC • 6x clock up to 100 MHz, LVDS bus • 2 of them connected to FPGA and ADC (user can choose clock for ADCs) • 4 clocks connected to FPGA, LVDS bus • IPMBus • Data 8 bits bus

  6. Stage of work • All schematics are done • Layouts are expected to be finished by the end of January • The prototype board is expected to be started by the end of February • Tests of the protoype board are expected to be done by the and of April

  7. Thank You for Your attention

More Related