1 / 9

Labs 5,6,7,9 of Boson NetSim

Labs 5,6,7,9 of Boson NetSim. Lab 5 – Saving Router Configuration. What is the config ?!! Contains commands that are executed when the device starts up Subject to back up, restore, FTP, … Running config is internally not a file, but generates corresponding file when persisted

yorick
Download Presentation

Labs 5,6,7,9 of Boson NetSim

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Labs 5,6,7,9 of Boson NetSim

  2. Lab 5 – Saving Router Configuration • What is the config?!! • Contains commands that are executed when the device starts up • Subject to back up, restore, FTP, … • Running config is internally not a file, but generates corresponding file when persisted • Two kinds of configs • Running config • The configuration currently in effect • Resides in RAM • Volatile: lost if device is restarted unless saved to NVRAM • Startup config • The configuration that takes effect when device starts up • Resides in NVRAM (non-volatile RAM)

  3. Lab 5 – Saving Router Configuration

  4. Lab 6 – Cisco Discovery Protocol (CDP) • The Cisco Discovery Protocol (CDP) is a proprietary Data Link Layer protocol developed by CiscoSystems • It is used to share information about other directly connected Cisco equipment • such as the operating system version and IP address • CDP can also be used for On-Demand Routing, which is a method of including routing information in CDP announcements so that dynamic routing protocols do not need to be used in simple networks • Cisco devices send CDP announcements to the multicast destination address 01-00-0c-cc-cc-cc, out each connected network interface

  5. Lab 6 – Cisco Discovery Protocol (CDP) •  By default, CDP announcements are sent every 60 seconds on interfaces • Each Cisco device that supports CDP, stores the information received from other devices in a table that can be viewed using the show cdp neighborscommand • The CDP table information is refreshed each time an announcement is received, and the holdtime for that entry is reinitialized • The holdtime specifies the lifetime of an entry in the table, if no announcements are received from a device for a period in excess of the holdtime, the device information is discarded (default 180 seconds)

  6. Lab 6 – Cisco Discovery Protocol (CDP) • Receiving and processing CDP information is still supported • CDP support was replaced with IEEE 802.1AB Link Layer Discovery Protocol (LLDP), an IEEE standard that is implemented by multiple vendors and is functionally similar to CDP

  7. Lab 7 – Configuration Router Interface • Router>enable • Router#config terminal • Router(config)#interface serial 0/0/0 • Router(config-if)#ip address 10.10.10.1 255.255.255.0 • Router(config-if)#no shutdown • Router#showip interface brief

  8. Lab 9 – Router Remote Access via Telnet • Telnet is a network protocol(Application layer protocol) used on the Internet or local area networks to provide a bidirectional interactive text-oriented communication facility using a virtual terminalconnection • User data is interspersed in-band with Telnet control information in an 8-bit byte oriented data connection over the TCP • Telnet was developed in 1969 beginning with RFC 15, extended in RFC 854 • Telnet provided access to a command-line interface (usually, of an operating system) on a remote host

  9. Lab 9 – Router Remote Access via Telnet • Most network equipment and operating systems with a TCP/IP stack support a Telnet service for remote configuration • However, because of serious security issues when using Telnet over an open network such as the Internet, its use for this purpose has waned significantly in favor of SSH • a user will be telnetting to a Unix-like server system or a network device (such as a router) and obtaining a login prompt to a command line text interface or a character-based full-screen manager

More Related