1 / 10

Introduction

MEASURING THE TEMPERATURE AT A DISTANCE USING TELEPHONY SYSTEM Automation seminar(telecommunication engineering) t94772(Siddhartha Lama). Introduction.

yasuo
Download Presentation

Introduction

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. MEASURING THE TEMPERATURE AT A DISTANCE USING TELEPHONY SYSTEMAutomation seminar(telecommunication engineering)t94772(Siddhartha Lama)

  2. Introduction • Telephone has become mainstay in modern communication. People can easily communicate with others around the world or in the office down the block without ever having to leave their desk. • They make information flow more efficient and timely as a result. We use the telephone for end to end communication. • The enhancement in end to end communication our purpose is a combination of the RF and the telephone. • To facilitate the communication effectiveness, here, we use RF module and the telephone line with DTMF to measure physical parameters like temperature (pressure, wind, ice, etc, time permitting) of remote area with the help of respective sensors.

  3. Objective The main objectives of this project are • Expand the capabilities of the existing communication. • Allow users to know the weather conditions of remote area and hardly accessible area. • To encourage the service providers to provide this facility in their communication services. • To enhance the communication services by allowing transmission of remote data • Tourism can be enhanced by knowing the remote area weather condition like Everest base campetc

  4. System Requirements HARDWARE: * LM 35 temperature sensor • 89c52 microcontroller • RF modules(FS 1000s) • DTMF encoder-um91215A • DTMF decoder-MT8870 • Crystal oscillators • NE 741(op-amp) • LCD(16 pin) Software: c programming, VHDL

  5. Block diagram

  6. Methodology The total hardware of the system can be broadly classified into nine units: • 1. input units. • 2. ADC units. • 3. Microcontroller units. • 4. RF units. • 5. DTMF encoder unit. • 6. Injection unit. • 7. Recover unit. • 8 . DTMF decoder unit. • 9. Output/display unit.

  7. Methodology • Signal conditioning of signal(data) from temperature sensor (LM 35) is performed with the help of zener diode and op-amp. • This signal is fed to the control mode ADC which gives 8 bit digital output by performing three functions namely sampling, quantization and encoding which is given to the input of microcontroller. • After serialization, these data are passed to the RF transmitter module through transmitting pin 3.1 of microcontroller. • RF transmitter module transmit data which is received by RF receiver module located at intermediate distance and passed to the microcontroller through the receiving pin 3.0 of microcontroller and finally to a port. • These data are loaded onto the DTMF encoder which gives corresponding tone. • Now, DTMF encoder output is injected onto the telephone line with the help of injection circuit. • The injected signal is recovered at the final destination end with the help of recover circuit. • The recovered signal is passed to the DTMF decoder circuitry which decodes DTMF tones into corresponding 4 bit digital data which is fed to the microcontroller. • Finally, after converting binary data into ASCII, the data are displayed on the LCD

  8. Expected Output • Our project is mainly aimed at the places which may not be connected to direct PSTN lines but the main PSTN office may be a little distance away from the area of concern. • We install sensors at that area and transmit the information conveyed by them to nearest telephone stations by the use of RF transmitter and receiver. • We then encode the information to sent via telephone lines and receive the output at the desired destination. • After decoding the data we could display the desired result in the users LCD.

  9. Conclusion • For the enhancement in end to end communication ,our purpose is a combination of the RF module and the telephone. To facilitate the communication effectiveness, here, we use RF module and the telephone line with DTMF to measure physical parameters like temperature (pressure, wind, ice, etc, time permitting) of remote area with the help of respective sensors.

  10. References • http://talkingelectronics.com/projects/circuitsonweb/circuitsonweb.html • http://www.8051projects.net/downloads 167.html • http://www.planet-source-code.com/vb/defult.asp?lngWid=3#categories

More Related