1 / 20

iKAGRA 初期アラインメント手順 Initial Alignment Procedure for iKAGRA

Step-by-step guide for the initial alignment of iKAGRA, including beam centering, beam profiling, and pointing adjustments for X and Y arms.

wojciechowski
Download Presentation

iKAGRA 初期アラインメント手順 Initial Alignment Procedure for iKAGRA

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. JGW-T1604823 January 4, 2020 iKAGRA初期アラインメント手順Initial Alignment Procedure for iKAGRA Yuta Michimura Department of Physics, University of Tokyo

  2. Expected Situation on Mar 2 EYA • All the mirrors (PR2, PR3, BS, ETMX, ETMY) installedwith actuation from digital system (pico, OSEMs, coils) • stable >250 mW fromIMC in high finessemode (s-pol) • both 3km ductsevacuated(φ100mm viewport oneach end; for Y arm,IYA+IYC also evacuated) GV closed evacuated GV opened IYA φ100mm viewports IYC φ150mm viewports GV closed from IMMT2 GV closed GV closed PRM PR3 PR2 BS IXC IXA EXA GV opened vented cleaned evacuated

  3. IMMT2 Alignment (Mar 3) EYA • Use picomotors on IMMT2 to center the beam on PR2 • PR3, PR2 chambersopened IYA IYC center the beam by looking at PR2 surface (beam radius 3.7mm) align IMMT2 PRM PR3 PR2 BS IXC IXA EXA

  4. PR2 Alignment (Mar 3) EYA • Use picomotors on PR2 to center the beam on PR3 • PR3, PR2 chambersopened IYA IYC align PR2 PRM PR3 PR2 BS IXC IXA EXA center the beam by looking at PR3 surface (beam radius 34mm)

  5. Beam Profiling at PR3 (Mar 3) EYA • Measure the profile of the beam going to PR3 • tilt PR2 temporarily • PR3, PR2 chambersopened IYA IYC tilt PR2 PRM PR3 PR2 BS IXC IXA EXA large beam profiler (beam radius 34 mm)

  6. PR3 Alignment (Mar 4) EYA • Use OSEMS on PR3 to center the beam on BS • PR3, PR2, BSchambers opened IYA IYC PRM PR3 PR2 BS IXC IXA EXA align PR3 center the beam by looking at BS surface (beam radius 34mm)

  7. Beam Profiling at IXA (Mar 4) EYA • Measure the beam profile at IXA • If not well collimated,move PR2 and iterate(it’s not easy to decideif collimated or notwith this length, butwe will do our best) • PR3, PR2, BS, IXAchambers opened IYA IYC PRM PR3 PR2 BS IXC IXA EXA large beam profiler (beam radius 34 mm) align PR3

  8. Pointing to X Arm (Mar 4-7) EYA • Put PD in EXA chamber, sweep PR3 alignment by OSEMs, and wait for the PDto get any signal(we will also putscreens + camerasto monitor EXA) • Put PD at EYA alsoto get signal by chance • PR3, PR2, BS, EXAchambers opened • If no success, go to plan B Thorlabs PDA100A (beam radius 40 mm) IYA IYC beam spot on GV 3.5195 mm ↑ from the center PRM PR3 PR2 BS IXC IXA EXA beam spot on GV 3.5195 mm ↑ from the center sweep PR3 alignment Thorlabs PDA100A (beam radius 40 mm)

  9. Beam Profiling at EXA (Mar 7) EYA • Measure the beam profile at IXA (this beam is clipped by φ100mm viewports) • PR3, PR2, BS, EXAchambers opened IYA IYC PRM PR3 PR2 BS IXC IXA EXA sweep PR3 alignment large beam profiler (beam radius 40 mm)

  10. Pointing Back from X Arm (Mar 8) EYA • Evacuate EXA if possible • Sweep ETMX alignment by coils, and wait for the PDto get any signal • PR3, PR2, BSchambers opened IYA IYC sweep ETMX alignment PRM PR3 PR2 BS IXC IXA EXA evacuate Thorlabs PDA100A (beam radius 40 mm)

  11. Back to IFI (Mar 8) EYA • Adjust ETMX alignment to center the reflected beam on BS, PR3, PR2, and get the beam back to IFI and then REFL port • PR3, PR2, BSchambers opened IYA IYC adjust ETMX alignment to IFI PRM PR3 PR2 BS IXC IXA EXA

  12. Close X arm (Mar 9) EYA • Put X arm bellows, and evacuate IXC + IXA (evacuate slowly; open arm GVafter IXC+IXA reached10-100 Pa) IYA IYC PRM PR3 PR2 BS IXC IXA EXA put duct evacuate

  13. Pointing to Y arm (Mar 9-10) EYA • Put PD in EYA chamber, sweep BS alignment by coils, and wait for the PDto get any signal • PR3, PR2, BS, EYAchambers opened Thorlabs PDA100A (beam radius 40 mm) beam spot on GV 16.0000 mm → from the center IYA IYC beam spot on GV 8.0000 mm → from the center sweep BS alignment PRM PR3 PR2 BS IXC IXA EXA

  14. Pointing Back from Y arm (Mar 11) EYA • Evacuate EYA if possible • Put PD in BS chamber, sweep ETMY alignment by coils, and wait for the PDto get any signal(block X arm beam) • PR3, PR2, BSchambers opened sweep ETMY alignment IYA IYC block X arm beam PRM PR3 PR2 BS IXC IXA EXA Thorlabs PDA100A (beam radius 40 mm)

  15. Get Fringe at REFL/AS (Mar 11) EYA • Unblock X arm beam and confirm fringing at REFL/AS • PR3, PR2, BSchambers opened IYA IYC block X arm beam PRM PR3 PR2 BS IXC IXA EXA Thorlabs PDA100A (beam radius 40 mm)

  16. Close Everything (Mar 12-13) EYA • Close remaining bellows and start evacuate the whole IFO (continue evacuationduring observation) IYA IYC evacuate PRM PR3 PR2 BS IXC IXA EXA put bellows

  17. Lock Michelson (Mar 14) EYA • Lock Michelson with REFL PD IYA IYC PRM PR3 PR2 BS IXC IXA EXA

  18. Plan B(if we don’t see the beam at EX)

  19. Evacuate Central Part (Mar 8) EYA • Put AS screen in BS chamber, put all the bellows, and evacuate the central part • Open gate valvesat IX/IY IYA IYC evacuate open this GV PRM PR3 PR2 BS IXC IXA EXA put bellows AS screen (beam radius 40 mm) Thorlabs PDA100A (beam radius 40 mm)

  20. All the rest • Pointing to X arm (Mar 9) • Back to IFI from X arm (Mar 10) • Pointing to Y arm (Mar 11) • Back to IFI from Y arm, and get fringing (Mar 12) • Evacuate EXA and EYA (Mar 13) • Lock Michelson (Mar 14) • We skip beam profiling at EXA • Use cameras/screens/irises(?) after evacuation of the central part

More Related