1 / 38

13. Subduction Zones William Wilcock

OCEAN/ESS 410. 13. Subduction Zones William Wilcock. Lecture/Lab Learning Goals. Be able to sketch the different kinds of convergent plate margins and label key processes Understand the processes in the “ subduction zone factory ” Understand the Wilson cycle

Download Presentation

13. Subduction Zones William Wilcock

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. OCEAN/ESS 410 13. Subduction ZonesWilliam Wilcock

  2. Lecture/Lab Learning Goals • Be able to sketch the different kinds of convergent plate margins and label key processes • Understand the processes in the “subduction zone factory” • Understand the Wilson cycle • Understand the different forces that drive subduction and that control the angle of the subducting slab. • Know the different kinds of earthquakes that occur in subduction zones • Be able to interpret focal mechanisms from subduction zone settings (LAB)

  3. 3 Types of Convergent Margin (Plate Boundary)

  4. Subduction zones are important because they are the downwelling branches in Earth’s mantle convection. • Subduction zones are responsible for some of the primary geologic processes on earth: • Convergence leads to the growth of continents by • volcanism • accretion of terrains • and loss of the continents by • Tectonic erosion • Sediment subduction • Subduction zone processes dominate the development of active geologic structures on the continents Subduction Zone Processes

  5. Subduction Factory

  6. Subduction Factory

  7. Mantle Geotherm Old Plate Peridotite SolidusWater lowers the melting temperature of mantle peridotite Wet Solidus >>1% water ~1 % water

  8. Wilson Cycle - Cyclical growth and loss of ocean basins leads to continental growth

  9. Passive Margin

  10. Convergent (Active) Margin

  11. Stable Continent Bigger than Stage A

  12. Tectonic Erosion

  13. Sediment Trapped Subduction

  14. The plate sinks under gravity (red arrow) according to its weight, thus how cold and dense it is. The slab also drags along adjacent mantle (black arrows). This mantle is pushed up against the subducting slab on the left hand side generating a high pressure region. The mantle is dragged down with the slab on the right hand side generating a low pressure. This pressure differential tends to lift the slab. Forces acting on a subducting slab Velocity Age Velocity

  15. Balance of Gravitational and Pressure Forces Influences Slab Dip Old (Cold) Plate & Slow Subduction Large gravitational force, small pressure force. Steep subduction angle Young (Warm) Plate & Fast Subduction Small gravitational force, large pressure force. Shallow subduction angle

  16. Earthquake Maximum Magnitude Subduction Rate, cm/yr Plate Age

  17. Slab Dips

  18. Island Arcs - Back Arc Spreading

  19. Back-Arc Spreading Two Ideas Subducting slab falls away Mantle flow in wedge creates extension

  20. Thermal Structure

  21. Deep Forces Resulting From Phase Changes Enhances Subduction Opposes Subduction

  22. Sometimes but not always mantle slabs do not penetrate 670 km discontinuity

  23. Subduction Zone Earthquakes

  24. Earthquakes Shallow Earthquakes Plate Boundary - Megathrust Surrounding Plates Deep Earthquakes Mineral phase changes as pressure increases and loss of water bearing minerals - incompletely understood

  25. Cascadia Locked Zone

  26. Cascadia Subduction ZoneLast earthquake 1700. Recurrence interval 200-1000 years (average = 500 years)

  27. Block diagram/cross section of tectonics

  28. Cascadia Warm slab implies dewatering at shallow depths and weak arc volcanism

  29. Deformation in Subduction Zones Accretionary Prism forms when sediments are present and scraped off subducting slab

  30. Oblique Subduction Leads to Shearing • This shearing also affects the forearc causing rotation of the strong Oregon block. • Compression of Puget Sound

More Related