1 / 17

Pseudo-NMOS

Pseudo-NMOS. Ratioed-logic Load is PMOS with gate tied to ground VOH is VDD. VOL is not ground. VOL= (Rpdn/Rload+Rpdn)*VDD At VOL PMOS is in saturation and NMOS is in triode. To get a low VOL ßn >>ßp.

viveca
Download Presentation

Pseudo-NMOS

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Pseudo-NMOS • Ratioed-logic • Load is PMOS with gate tied to ground • VOH is VDD. VOL is not ground. • VOL= (Rpdn/Rload+Rpdn)*VDD • At VOL PMOS is in saturation and NMOS is in triode. • To get a low VOL ßn >>ßp. • For a faster low to high transition the current should be high and hence bigger ßp required. CONFLICT!!

  2. Problems and Advantages of Pseudo-NMOS Problems : Voltage transfer characteristic is asymmetrical Rise and fall time are asymmetrical Static power consumption Advantages: High speed Useful when designing complex gates with large fan-in.

  3. Dynamic Combinational Logic • Avoids static power dissipation • Uses a sequence of pre-charge and Evaluate to realize complex logic functions. • The inputs to the logic are not allowed to change and are zero in pre-charge phase. • Pre-charge phase when phi=0 and Evaluate when phi=1. • If the output is discharged it can not be charged again. • tpLH=0! And tpHL depends on the pull down network.

  4. Advantages of Dynamic Combinational logic over static combinational logic • Number of transistors are less N+2 compared to 2N. • Non-Ratioed. • No static power consumption • High switching speed.

  5. Problems Associated with dynamic logic • Charge leakage • Charge sharing • Clock feed through

  6. Cascading Dynamic gates • Problem arises when Dynamic gates are cascaded. • The PDN of second stage is in a conducting stage. This leads to faulty operation of the gates. • Correct operation is guaranteed as long as the inputs make a single 0-1 transition.

  7. Domino Logic • Consists of a Phin block followed by a static inverter. • Inverter ensures that there is only 0-1 transition during evaluation mode. • During pre-charge all inputs a(except external inputs) ate set to zero. During Evaluation the output of first domino stays at 0 or makes a 0-1 translation affecting the second domino. • Only non-Inverting logic can be implemented. • Very high speeds can be achieved. • Useful for large fan-out circuits like ALU.

  8. NP-CMOS • Faster than domino logic because of the elimination of static inverters • The inverter can be avoided by exploiting the duality between the phin and phip blocks. • Phip and phin blocks are clocked with inverse clock to make evaluation and pre-charge time coincide.

  9. Dynamic Sequential Logic C2MOS Latch • Insensitive to clock overlap. • Made of Phi and Phib sections • When phi=1 , phi is in evaluation mode and phib in hold mode. • When phi=0, phi is on hold and phib in evaluation.

  10. Dynamic sequential Circuits NORA – CMOS • For implementing Fast Pipelined data-path • Combines C2MOS registers and np-CMOS dynamic logic. • Logic and Latch clocked in such a way that both are simultaneously in evaluation or hold( precharge ) mode

  11. Dynamic sequential Circuits • C2MOS based circuit is race free as long as all the logic functions implemented between latches are non-inverting. • During overlap only pull-up or pull-down is activated. • Figure shows a 1-1 overlap.The only way race can happen is if the function is inverting.

  12. Dynamic sequential Circuits • Figure shows phi and phib modules. • When phi=0 for phi block logic is in precharge and latch is in Hold and for phib block logic and latch are in evaluate. • When phi=1 for phi block logic and latch are in evaluate and for phib block logic is in precharge and latch in hold. • Consists of chain of alternating phi and phib blocks.

  13. Dynamic sequential logic Design rules for NORA-CMOS • Inputs to the dynamic phin( phip) block are allowed to make only a single 0-1(1-0) transition. • In order to avoid races the number of inversion between latches should be even. • If dynamic nodes nodes are present , the number of static inverters between latch and dynamic gate in logic block should be even.

  14. True Single Phase Clocking • Only a single clock is needed to correctly operate a dynamic-sequential circuit. • The latches are modified as shown • For a doubled n-C2MOS latch when phi is high, the latch is in evaluation and when phi is low it is in hold. • All constraints are removed. • Races are eliminated.

  15. TSPC • As shown in the figure the logic can be implemented inside the latch or between the latch. • The latch can be further modified so that the clock load is reduced by half and the number of transistors reduced. • Not all nodes experience full voltage swing in this case.

  16. TSPC • D-Flip Flop implementation using TSPC.

More Related