1 / 11

WAN Protocols

WAN Protocols. PPP (Point to Point protocol). WAN Encapsulation Protocols. On WAN connection, the protocol depends on the WAN technology and communicating equipment: Examples: HDLC – The default encapsulation type on point-to-point connections, Cisco devices ONLY.

Download Presentation

WAN Protocols

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. WAN Protocols PPP (Point to Point protocol)

  2. WAN Encapsulation Protocols • On WAN connection, the protocol depends on the WAN technology and communicating equipment: • Examples: • HDLC – • The default encapsulation type on point-to-point connections, • Cisco devices ONLY. • PPP - Provides router-to-router and host-to-network connections. • Frame Relay - Frame Relay eliminates some of the time-consuming processes • ATM - The cell relay in which devices send multiple service types (voice, video, or data) in fixed-length (53-byte) cells. With SLIP, you have to know the IP address assigned to you by your service provider. You also need to know the IP address of the remote system you will be dialing into. You may also need to configure such details as MTU (maximum transmission unit), MRU (maximum receive unit), etc.

  3. What is PPP? • When you need to connect to a non-Cisco router, you should use PPP encapsulation. • PPP includes many features: • The link quality management • If too many errors are detected, PPP takes the link down. • PPP supports authentication.

  4. PPP Configuration Options • PPP may include the following options: • Authentication - Peer exchange authentication messages. • Password Authentication Protocol (PAP) and • Challenge Handshake Authentication Protocol (CHAP). • Compression – • Increases the effective throughput on PPP connections by reducing the amount of data in the frame that must travel across the link. • Two compression are Stacker and Predictor. • Error detection - Identifies fault conditions. • The Quality and Magic Number options help ensure a reliable, loop-free data link. • Multilink - Cisco IOS Release 11.1 and later supports multilink PPP. • This alternative provides load balancing over the router interfaces that PPP uses. • PPP Callback - • The client makes the initial call, requests that the server call it back, and terminates its initial call.

  5. PPP Configuration Options • PPP can be configured to support: • Authentication using either PAP or CHAP • Compression using either Stacker or Predictor • Multilink which combines two or more channels to increase the WAN bandwidth

  6. PPP Configuration Commands • Example 1: Enabling PPP on an Interface • To set PPP as the encapsulation method used by a serial interface, use the encapsulation ppp interface configuration command. • R3#configure terminal • R3(config)#interface serial 0/0 • R3(config-if)#encapsulation ppp • You must first configure the router with an IP routing protocol to use PPP encapsulation. • Example 2: Compression • You can configure point-to-point compression on serial interfaces after you have enabled PPP. Because this option invokes a software compression process, it can affect system performance. If the traffic already consists of compressed files (.zip, .tar, or .mpeg, for example), do not use this option. • R3(config)#interface serial 0/0 • R3(config-if)#encapsulation ppp • R3(config-if)#compress [predictor | stac] Why?

  7. PPP Configuration Commands • Example 3: Link Quality Monitoring • LCP provides an optional link quality determination phase. • If the link quality percentage is not maintained, the link is deemed to be of poor quality and is taken down. • This example configuration monitors the data dropped on the link and avoids frame looping: • R3(config)#interface serial 0/0 • R3(config-if)#encapsulation ppp • R3(config-if)#ppp quality 80 • Example 4: Load Balancing Across Links • Multilink PPP provides a method for spreading traffic across multiple physical WAN links while providing packet fragmentation and reassembly, proper sequencing, multivendor interoperability, and load balancing on inbound and outbound traffic. • Router(config)#interface serial 0/0 • Router(config-if)#encapsulation ppp • Router(config-if)#ppp multilink

  8. Verified a Serial PPP Encapsulation Configuration • Use the show interfaces serial command to verify proper configuration of HDLC or PPP encapsulation. • When you configure HDLC, the output of the show interfaces serial command should show "encapsulation HDLC". • When you configure PPP, you can check its LCP and NCP states.

  9. PPP Authentication Protocols • PPP defines an extensible LCP that allows negotiation of an authentication protocol for authenticating its peer before allowing network layer protocols to transmit over the link. • PAP is a very basic two-way process. • There is no encryption-the username and password are sent in plain text. If it is accepted, the connection is allowed. • CHAP is more secure than PAP. It involves a three-way exchange of a shared secret.

  10. Challenge Handshake Authentication Protocol (CHAP) • Once authentication is established with PAP, it essentially stops working. This leaves the network vulnerable to attack. • CHAP conducts periodic challenges to make sure that the remote node still has a valid password value. • The password value is variable and changes unpredictably while the link exists. • After the PPP link establishment phase is complete, • The router sends a challenge to the remote node. • The remote node responds with a value calculated using a one-way hash function using MD5. • The local router checks the response against its own calculation of the expected hash value. If the values match, the initiating node acknowledges the authentication. Otherwise, it immediately terminates the connection. • Because the challenge is unique and random, the resulting hash value is also unique and random.

  11. Configuring PPP with Authentication • The procedure outlined in the table describes how to configure PPP encapsulation and PAP/CHAP authentication protocols.

More Related