1 / 35

Undulator Effective-K Measurements Using Angle-Integrated Spontaneous Radiation

Undulator Effective-K Measurements Using Angle-Integrated Spontaneous Radiation. Bingxin Yang and Roger Dejus Advanced Photon Source Argonne National Lab. Some History of the Conceptual Development. 1998 - 2002: APS Diagnostics Undulator e-beam energy measurement

stella
Download Presentation

Undulator Effective-K Measurements Using Angle-Integrated Spontaneous Radiation

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Undulator Effective-K MeasurementsUsing Angle-Integrated Spontaneous Radiation Bingxin Yang and Roger Dejus Advanced Photon Source Argonne National Lab

  2. Some History of the Conceptual Development • 1998 - 2002: APS Diagnostics Undulator e-beam energy measurement • Using angle-integrated undulator radiation measure stored e-beam energy change • Jan. 20, 2004: UCLA Commissioning workshop • Galayda wish list for spontaneous radiation measurements • Feb. 10, 2004: X-ray diagnostics planning meeting (John Arthur) • Roman: Not possible to measure Keff with required accuracy DK/K~1.5×10-4 • Sep. 22, 2004: SLAC Commissioning workshop • Bingxin Yang: Keff can be measured with required accuracy • Large aperture improves accuracy • Electron energy jitter is the main experimental problem • Two undulator differential measurement improves speed and accuracy over single undulator measurements. • Oct., 2004: LCLS • Jim Welch: Keff can be measured with required accuracy • Small aperture is better • Spectrometer allows fast data taking • Apr. 18, 2005: Zeuthen FEL Commissioning workshop • Bingxin Yang: Undulator mid-plane can be located within 10 mm • Regular observation can monitor systematic changes in undulators • Jim Welch:

  3. Hope for this workshop • Form a consensus • Spontaneous spectral measurements can be used to measure Keff with required accuracy (DK/K~1.5×10-4) • Aperture size should not be an issue • Operational experience will decide it naturally • Make decisions on the monochromator / spectrometer issues • Monochromator (simple, low cost, robust) • Differential measurements (ultra-high resolution, dependable, other uses: vertical alignment, monitor field change / damage quickly • Spectrometer (scientific experiments) • Need to evaluate specs / cost / schedule / R & D / risk factors / operational availability / maintenance effort • Decisions may depend on other functions • My personal bias: machine diagnostics

  4. Outline • Features of the spontaneous spectrum and effect of beam quality: numerical calculations • Average properties: e-beam divergence (sx’, sy’), x-ray beam divergence (sw), and energy spread (sg) • Aperture geometry: width and height, center offset, and undulator distances • Magnetic field errors • Effects of e-beam jitter: simulated experiments • Beamline Option 1: crystal monochromator with charge, energy and trajectory angle readout • Beamline Option 2: crystal monochromator with differential undulator setup • High-resolution experiment: locating magnetic mid-plane of the undulator. Dependence on beam centroid position (x, y) • Summary

  5. Spontaneous Radiation Spectrum

  6. Angle-integrated? How large is the aperture! Pinhole (sinc) < << Angle-integrated (numeric) BXY: Large enough for the edge feature to be stable

  7. Related publications • Momentum compaction measurements • B.X. Yang, L. Emery, and M. Borland, “High Accuracy Momentum Compaction Measurement for the APS Storage Ring with Undulator Radiation,” BIW’00, Boston, May 2000, AIP Proc. 546, p. 234. • Energy spread measurements • B.X. Yang, and J. Xu, “Measurement of the APS Storage Ring Electron Beam Energy Spread Using Undulator Spectra,” PAC’01, Chicago, June 2001, p. 2338 • RF frequency / damping partition fraction manipulations • B. X. Yang, A. H. Lumpkin, ‘Visualizing Electron Beam Dynamics and Instabilities with Synchrotron Radiation at the APS,” PAC’05 • DK/K simulations • B. X. Yang, “High-resolution undulator measurements Using angle-integrated spontaneous radiation,” PAC’05

  8. How large is the aperture! FEL-relevant Capture the radiation cone: 2.35 – 5 rms radius  17 – 37 mrad Measured radiation spectrum is more important that calculated from field data!

  9. Marking the location of a spectral edge We will watch how the following property changes: • HALF PEAK PHOTON ENERGY

  10. Effects of Aperture Change (Size and Center) • Plot the half-peak photon energy vs. aperture size • Edge position stable for 25 – 140 mrad  100 mrad best operation point • Independent of aperture size  Independent of aperture center position

  11. Effects of Aperture Change (Source distance) • Calculate flux through an aperture satisfying: • ≤ 100 mrad • ≤ allowed by chamber ID • Plot half-peak photon energy • Rectangular aperture reduces variation

  12. Effects of Finite Energy Resolution • Four factors contribute to photon energy resolution • Electron beam energy spread (0.03% RMS  X-ray energy width = 11.7 eV FWHM) • Monochromator resolution (DwM/w ~ 0.1% or 8 eV) • Photon beam divergence Dqw ~ 2.35/gN1/2 ~ 8 mrad • Electron beam divergence sy’ ~ 1.2 mrad

  13. Effect of Finite Energy Resolution • Edge position moves with increasing energy spread

  14. Effects of Undulator Field Errors Monte Carlo integration for 10 K particle histories. Electron beam parameters E = 13.640 GeV sx = 37 mm sx’ = 1.2 mrad sg/g = 0.03% Detector Aperture 80 mrad (H) 48 mrad (V)

  15. Comparison of Perfect and Real Undulator SpectraFilename: LCL02272.ver; scaled by 0.968441 to make Keff = 3.4996 • First harmonic spectrum changes little at the edge.

  16. Comparison of Perfect and Real Undulator Spectra • Changes in the third harmonic spectrum is more pronounced. But the edge region appears to be usable. • Changes in the fifth harmonic spectrum is significant. Not sure whether we can use even the edge region.

  17. Summary of calculations so far • The following beam qualities are not problems for measuring spectrum edge: • e-beam divergence (sx’, sy’), • x-ray beam divergence (Dqw ), • energy spread (sg) and monochromator resolution, • aperture width and height, center offset, and • undulator distances • Magnetic field errors • Preliminary results show that the first harmonic edge is usable. Third harmonic edge may also be usable. • How to define effective K in the presence of error is not a trivial issue. I need to learn more to understand it (BXY). • Next we move on jitter simulations.

  18. Jitters and Fluctuations • Bunch charge jitter • X-ray intensity is proportional to electron bunch charge (0.05% fluctuation). • Electron energy jitter • Location of the spectrum edge is very sensitive to e-beam energy change (10-5 noise): Dw/w = 2·Dg/g • Electron trajectory angle jitter • Trajectory angle (0.24 mrad jitter) directly changes grazing incidence angle of the crystal monochromator Damaging effect! Use simulation to assess impact.

  19. Beamline Option 1: Poor man’s solution • One reference undulator • One flat crystal monochromator (asymmetrically cut preferred) • One flux intensity detector • One hard x-ray imaging detector • Beamline slits (get close to 100 mrad) Operation procedure for setting Keff • Pick one reference undulator (U33) and measure a full spectrum by scanning the crystal angle (angle aperture ~ 100 mrad) • Position the crystal angle at the mid-edge and record n-shot (n = 10 –100) data of the x-ray flux intensity (FREF) with electron energy, trajectory angle, and charge • Roll out reference undulator and roll in other undulator one at a time. • Set slits to 100 mrad or best available • Adjust x-position until the n-shot x-ray flux intensity data matches FREF. • Use the measured electron bunch data in real-time to correct for jitters

  20. Measure fluctuating variables • Charge monitor: bunch charge • OTR screen / BPM at dispersive point: energy centroid • Hard x-ray imaging detector: electron trajectory angle (new proposal)

  21. One Segment Simulation: Approach

  22. Effect of electron energy “correlation” Define “Correlated Electron-Photon Energy” RMS error from simulation

  23. Summary of 1-undulator simulations(charge normalized and energy-corrected) • Applying correction with electron charge, energy and trajectory angle data shot-by-shot greatly improves the quality of data analysis at the spectral edge. • Full spectrum measurement for one undulator segment (reference) • The minimum integration time to resolve effective-K changes is 10 – 100 shots with other undulator segment (data processing required) • As a bonus, the dispersion at the flag / BPM can be measured fairly accurately. • Not fully satisfied: • Rely heavily on correction calibration of the instrument • No buffer for “unknown-unknowns” • Non-Gaussian beam energy distribution ???

  24. Beamline Option 2: Ultra-high Resolution • Reference Undulator (U33) • Period length and B-field same as other segments • Zero cant angle • Field characterized with high accuracy • Upstream corrector capable of 200 mrad steering (may be reduced if needed). • Broadband monochromator (DE/E ~ 0.03%) • Improves photon statistics • Suppress coherent intensity fluctuations • Big area, large dynamic range, uniform, linear detector • Hard x-ray imaging detector (trajectory angle)

  25. Operation Procedures for setting Keff (BL2) • Steer the beam to be away from the axis in the reference undulator (U33) and measure a full spectrum by scanning the crystal angle (angle aperture ~ 100 mrad) • Position the crystal angle at the mid-edge • Roll in other undulator one at a time (test undulator). • Adjust the x-position of the test undulator until the x-ray intensities of the two undulator matches (difference < threshold). • Use the measured electron beam angle data in real-time to correct for angle jitters if necessary

  26. Differential Measurements of Two Undulators • Insert only two segments in for the entire undulator. • Steer the e-beam to separate the x-rays Use one mono to pick the same x-ray energy Use two detectors to detect the x-ray flux separately Use differential electronics to get the difference in flux

  27. Signal of Differential Measurements • Select x-ray energy at the edge (Point A). • Record difference in flux from two undulators. • Make histogram to analyze signal quality • Signals are statistically significant when peaks are distinctly resolved DK/K =  1.5  10-4

  28. Summing multi-shots improves resolution • Summing difference signals over 64 bunches • Distinct peaks make it possible to calculate the difference DK at the level of 10-5. Example: Average improves resolution for DK/K =  10-5

  29. Differential Measurement Recap • Use one reference undulator to test another undulator simulataneously • Set monochromator energy at the spectral edge • Measure the difference of the two undulator intensity Simulation gives approximately: • To get RMS error DK/K < 0.710-4, we need only a single shot (0.2 nC)! • We can use it to periodically to log minor magnetic field changes, for radiation damage. • Any other uses?

  30. Other application of the techniques:Search for the neutral magnetic plane • Set the monochromator at mid-edge (Point A). • Insert only one test segment in. • Move the undulator segment up and down, or move electron beam up and down with a local bump. • When going through the plane of minimum field (neutral plane), the spectrum edge is highest in energy. Hence the photon flux peaks. • After the undulator is roughly positioned, taking turns to scan one end at a time, up and down, to level it.

  31. Simulation of undulator vertical scan • Charge normalization only: ~ 20K shots / point • Charge-normalized and electron-energy corrected: ~ 512 shots / point • Differential measurements (two undulators): ~ 16 shots /point gives us RMS error ~ 1.0 mm ?!

  32. Conclusion for Locating Magnetic Neutral Plane • Both techniques can be used to search the magnetic neutral plane, each has its own advantages and disadvantages: • Single undulator measurement (with charge-normalization and e-beam energy correction) can get required S/N ratio after averaging. • Differential measurement has best sensitivity, need shortest time (keep up with mechanical scan), but required more hardware. • Finite beam sizes and centroid offset (in undulator) shift spontaneous spectrum: the apparent K is given by

  33. Summary (The Main Idea) • We propose to use angle-integrated spectra (through a large aperture, but radius < 1/g) for high-resolution measurements of undulator field. • Expected to be robust against undulator field errors and electron beam jitters. • Simulation shows that we have sufficient resolution to obtain DK/K <  10-4 using charge normalization. Correlation of undulator spectra and electron beam energy data further improves measurement quality. • A Differential technique with very high resolution was proposed: It is based on comparison of flux intensities from a test undulator with that from a reference undulator. • Within a perfect undulator approximation, the resolution is extremely high, DK/K =  3  10-6 or better. It is sufficient for XFEL applications. • It can also be used for routinely logging magnet degradation.

  34. Summary (Continued) • Either beamline option can be used for searching for the effective neutral magnetic plane and for positioning undulator vertically. The simulation results are encouraging (resolution ~1 mm in theory for now, hope to get ~ 10 mm in reality). What’s next • Sources of error need to be further studied. Experimental tests need to be done. • More calculation and understanding of realistic field • Longitudinal wake field effect, • Experimental test in the APS 35ID • More?

  35. Monochromator Recommendation • A dedicated monochromator for undulator measurement (low cost and robust, permanently installed). • Use it for DK/K measurements • Use it for regular vertical alignment check • Use it for routine magnetic field measurements at regular intervals (after routine BBA operation). • Logging magnetic field changes to see trend of damage, identify sources / mechanism for damage • Look for most damaged undulator segments for service for next shutdown • Location of the monochromator • Front end  easy to service. Too crowded? • In tunnel OK. • Differential measurement strongly recommended • But steering magnet can be added later as an upgrade. • Differential measurement saves time, improves accuracy. • Spectrometer will be easily justified by the science it supports.

More Related