1 / 21

Module 7 Chapter 6 Ethernet Technologies

Module 7 Chapter 6 Ethernet Technologies. 10-Mbps Ethernet. Legacy Ethernet 10BASE5, 10BASE2, and 10BASE-T Four common features of Legacy Ethernet Timing parameters Frame format Transmission process Basic design rule. 10-Mbps Ethernet. 10BASE5. 10-Mbps Ethernet. 10BASE2.

sen
Download Presentation

Module 7 Chapter 6 Ethernet Technologies

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Module 7Chapter 6 Ethernet Technologies

  2. 10-Mbps Ethernet • Legacy Ethernet • 10BASE5, 10BASE2, and 10BASE-T • Four common features of Legacy Ethernet • Timing parameters • Frame format • Transmission process • Basic design rule

  3. 10-Mbps Ethernet 10BASE5

  4. 10-Mbps Ethernet 10BASE2

  5. 10-Mbps Ethernet 10BASE-T

  6. Wiring and Architecture • 5-4-3 rule • No more than fivesegments • Separated by no more than four repeaters. • No more than three populated segments between any two distant stations • Hubs or repeaters merely extend the length of a network segment within a single collision domain • Bridges and switches divide a segment into separate collision domains

  7. Manchester Encoding • Manchester encoding is used in 10 Mbps systems • The direction of the edge transition in the middle of the timing window determines the binary value

  8. 100-Mbps Ethernet • 100-Mbps Ethernet is also known as Fast Ethernet • 100BASE-TX is copper UTP • 100BASE-FX is multimode optical fiber • Three common characteristics: • Timing parameters • Frame format • Parts of the transmission process

  9. 100-Mbps Ethernet • Timing parameters • One bit time in 100-Mbps Ethernet is 10nsec • Frame format • 100-Mbps frame format is the same as the 10-Mbps frame • Parts of the transmission process • Two separate encoding steps are used • The first part of the encoding uses a technique called 4B/5B • The second part of the encoding is the actual line encoding specific to copper or fiber

  10. 100-Mbps Ethernet • 100BASE-TX uses 4B/5B encoding which is then scrambled • Converted to multi-level transmit-3 levels or MLT-3. • Half-duplex = 100 Mbps • Full-duplex = 200 Mbps

  11. Fast Ethernet Architecture • Fast Ethernet links consist of a connection between a station and a hub or switch • Hubs are considered multi-port repeaters • Switches are considered multi-port bridges • These are subject to the 100 m UTP distance limitation

  12. Fast Ethernet Architecture • Class I repeater • Any repeater that changes between one Ethernet implementation and another • 140 bit-times of latency • Class II repeater • 92 bit-times latency • Cable between Class II repeaters may not exceed 5 meters

  13. Fast Ethernet Architecture • Signaling scheme is inherently full duplex • Half duplex are not uncommon • Half duplex is undesirable • Switches have made the 100m limitation less important • Workstations are located within 100m of the switch • 100 m distance starts over at the switch

  14. 1000-Mbps Ethernet • 1000-Mbps Ethernet or Gigabit Ethernet Transmission • Fiber and copper media   • The 1000BASE-X IEEE 802.3z • Specifies 1 Gbps full duplex over optical fiber • 1000BASE-TX, 1000BASE-SX, and 1000BASE-LX • Timing parameters • 1 nanosecond or 1 billionth of a second bit time. • Frame Format • Same format used for 10 and 100-Mbps Ethernet • Transmission • Depending on the implementation

  15. 1000-Mbps Ethernet • 1000BASE-T (IEEE 802.3ab) was developed to provide additional bandwidth for: • Intra-building backbones • Inter-switch links • Server farms • Connections for high-end workstations • Supports both half-duplex and full-duplex • Fiber-based Gigabit Ethernet (1000BASE-X) • Uses 8B/10B encoding (similar to 4B/5B) • This is followed by Non-Return to Zero (NRZ) line encoding

  16. 1000Base-LX/SX • Common to all versions of 1000 Mbps • Timing • Frame format • Transmission • NRZ signals are pulsed into the fiber • Short-wavelength (1000BASE-SX ) • Long-wavelength (1000BASE-LX) • Media Access Control • Link as point-to-point • Separate fibers • Transmitting (Tx) • Receiving (Rx) • Inherently full duplex

  17. GigabitEthernet • Gigabit Ethernet is the dominant technology for: • Backbone installations, • High-speed cross-connects • General infrastructure

  18. 10 GigabitEthernet • IEEE 802.3ae, governs the 10GbE family • Provide increased bandwidth • Interoperable with existing infrastructure • Implementations being considered: • 10GBASE-SR • 10GBASE-LX4 • 10GBASE-LR and 10GBASE-ER • 10GBASE-SW, 10GBASE-LW, and 10GBASE-EW

  19. 10 GigabitEthernet • 10GBASE-SR – • short distances, supports a range between 26 m to 82 m • 10GBASE-LX4– • Uses wide wavelength division multiplexing (WWDM) • 240 m to 300 m over multimode fiber • 10 km over single-mode fiber • 10GBASE-LR and 10GBASE-ER – • Support 10 km and 40 km over single-mode fiber • 10GBASE-SW, 10GBASE-LW, and 10GBASE-EW – • Known collectively as 10GBASE-W • Works with OC-192 synchronous transport module

  20. Future of Ethernet • The future of networking media is three-fold: • Copper (up to 1000 Mbps, perhaps more) • Wireless (approaching 100 Mbps, perhaps more) • Optical fiber (currently at 10,000 Mbps and soon to be more) • Copper and wireless media have certain physical and practical limitations • Limitations on optical fiber are: • Electronics technology • emitters and detectors • Fiber manufacturing processes • Developments in Ethernet • Heavily weighted towards Laser light sources • Single-mode optical fiber

  21. The End Break Time

More Related