'Branch circuit' presentation slideshows

Electrical

Electrical. Safety. For The Poultry Industry. Disclaimer. This module was developed for the poultry industry. The presentation is not inclusive of all of the safety related work practices in the workplace, especially, those required to prevent injuries from arc flash or blast.

897 views • 79 slides

DAY 4 CHAPTER 3 CONDUCTOR SIZES,TYPES, ETC.

DAY 4 CHAPTER 3 CONDUCTOR SIZES,TYPES, ETC. Continuous Load. A load where the maximum current is expected to continue for 3 hours or more. Continuous loads shall not exceed 80% of the rating of the Branch circuit. CIRCUIT BREAKERS ARE THE FINAL OVERCURRENT PROTECTION DEVICE.

1.07k views • 59 slides

The Motor Protection Consultants

The Motor Protection Consultants. U L Tested. A Guide to Applying. Motor Circuit Controllers. According to NEC and UL. Start from the Top. Direct Access Menu You may jump directly to the desired section by selecting from the menu below. NEC 100 Definitions.

811 views • 52 slides

David S. Ingalls Rink New Haven, CT Yale University Eero Saarinen 61,646 sf 2

Building name Location Building Occupant Architect Total gsf Total Levels. David S. Ingalls Rink New Haven, CT Yale University Eero Saarinen 61,646 sf 2. Client Architect Lighting Consultant Structure Engineers Mechanical Consultants Construction Manager Civil Engineer

694 views • 33 slides

EE4503 Electrical Systems Design

EE4503 Electrical Systems Design. Branch circuit and Feeder (Lighting and Appliances). Topics. Characteristics of Loads Circuits Design Branch Circuit Feeder Circuit Load Schedule. Characteristics of Loads. Continuous Load

638 views • 29 slides

DC ELECTRICAL CIRCUITS

DC ELECTRICAL CIRCUITS. RESISTANCE. DC ELECTRICAL CIRCUITS. In short resistance limits the flow of current. Resistance is measured in ohms, the symbol used to refer to resistance is the omega symbol ? . The letter R is used to represent resistance when working with formulas.

440 views • 27 slides

Introduction to Circuits Analysis

Introduction to Circuits Analysis. by Andrew G. Bell abell118@ivytech.edu (260) 481-2288 Lecture 5. CHAPTER 5. Parallel Circuits. Parallel Circuit Characteristics. There are two or more paths for current flow The voltage is the same across all parallel branches. A Practical Example.

442 views • 27 slides

Basic House Wiring

Basic House Wiring. Electrical Measurement Terms. Amp - measures the rate of flow of electrical current Volt - measure of pressure or force pushing electricity Ohm - measure of electrical resistance Watt - basic measure of electricity (amps x volts = watts). Other Basic Terms.

678 views • 26 slides

BRANCH CIRCUITS

BRANCH CIRCUITS. Branch Circuit-separate electrical [path independent of other circuits sized by the overcurrent protection device. Electrical load- amount of power required for the branch circuit. LIGHTING LOADS.

1.23k views • 18 slides

COMMERCIAL ELECTRICAL (Chapter 11)

462 views • 17 slides

COMMERCIAL ELECTRICAL (Chapter 11)

306 views • 17 slides

1) What area are you most nervous about for the midterm?

1) What area are you most nervous about for the midterm?. Residential electrical systems Commercial electrical systems Panel and branch circuit sizing Lamp technology and light level requirements CU calculations and fixture calculations. Objectives. Review material for midterm

232 views • 16 slides

Topic 7 - Electricity in the Home

Topic 7 - Electricity in the Home . Transmission of Electricity through the Power Grid Tranformers are used to change the amount of voltage with hardly any energy loss.

491 views • 15 slides

HVAC Wiring

Understanding Wiring. HVAC Wiring. Wiring diagrams are road maps for electron flow. HVAC Wiring. HVAC Technicians must know: How to draw them How to read them. HVAC Wiring. Drawing diagrams Begin with a description of how the circuit is too work . HVAC Wiring.

891 views • 15 slides

SCCR Applying High Fault Ratings Component HOTT

262 views • 15 slides

EE4503 Electrical Systems Design

EE4503 Electrical Systems Design. Load Calculation. Topics. Load Calculation (E.I.T.) Load Calculation by Adding Branch Circuit Load Calculation for condominium Load Estimation. Load Calculation (E.I.T.) lighting. Load Calculation (E.I.T.) receptacles.

758 views • 14 slides

Unit 2 Assignment Checklist

190 views • 11 slides

Wiring Accessories

Wiring Accessories. Energy & Environment. Electrical Accessories. Why might we use electrical accessories?. Protection . Adjustment of resistance. Control. The standard current ratings of the accessories are 6, 16 & 32 ampere. The voltage rating is 240V AC . Switches.

2.36k views • 10 slides

North Carolina Department of Insurance Office of State Fire Marshal Risk Management

North Carolina Department of Insurance Office of State Fire Marshal Risk Management State Electrical Division 2017 State Electrical Code 210.8(A)( 4) - GFCI Protection in a Crawl Space. Notice:

255 views • 7 slides

EE4503 Electrical Systems Design

EE4503 Electrical Systems Design. Introduction. Textbook & Resources. Electrical Systems Design ( ????????? ?????????) ???????????????????????????????????????? ?.?. 2545 (Thai Electrical Code 2002: EIT Standard 2001-51). Topics. Introduction to Electrical Systems Design Cables

463 views • 6 slides