1 / 2

Plumber in Glendale, AZ

At Deer Valley Plumbing Contractors our Phoenix plumbers offer residential and commercial services backed by 30 years’ experience and the latest technology.

Download Presentation

Plumber in Glendale, AZ

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. How To Fix Low Water Pressure in the Shower If you’re wondering how to fix low water pressure in the shower, we’ve got the solution for you. The most common reason a shower has low pressure stems from the flow restrictor. Our step by step guide will walk you through the process of unclogging your shower head, eliminating your low water pressure, and restoring your beloved bathing time – all within 30 minutes. What Could Be Wrong With Low Water Pressure In The Shower If you purchased your home as a new-build and the low water pressure in the shower has been chronic since move-in day, chances are that the issues stem with the initial installation. You see, it is not uncommon for small pieces of solder, copper shavings, wood dust, wood chips, globs of soldering flux, pieces of plastic, etc. to enter the water lines when the water supply lines are installed. However, it is the responsibility of the plumber to flush out the water supply lines before any fixtures are installed. If the lines are not flushed before the shower head is installed, the rapidly flowing water may carry a mixture of water and debris into the shower head. This may cause the extremely small holes in the flow restrictor to become clogged or partially clogged in just a few seconds. Some of you may have a shower head that worked fine but the flow has reduced over time. If this is the case, you may have pieces of sediment or debris from the city water system or your well is clogging the restrictor. This is not uncommon, especially for homes fed by older city water mains. For example, if a city water main is serviced, pieces of sediment can dislodge in the main water line and flow towards your house. The main line that feeds your home might become partially blocked, affecting the water pressure. Or the giant clog is broken apart allowing smaller pieces of sediment to reach and block the shower head. How To Fix Low Water Pressure In The Shower: Flow Restrictor 1. Detach the shower head from the angled pipe that projects out from the wall. 2. With the shower head off, turn on the water to the shower to inspect the flow from the angled wall pipe. If a reasonable about of water flows, chances are the problem is in the shower head. If water does not flow, you may need to have the water line flushed with the help of a plumber. 3. If the problem is in the showerhead, look at the end of the shower head where the angled wall pipe connected to it. You should see a small plastic disk. If no plastic disk is visible, skip to Step 10. 4. Using a thin pointed piece of metal, carefully pry the disk out of the shower head. Go slowly so you don’t fling the disk out and lose it. Also, you’ll need to reinstall the disk exactly as it sit before you remove it, so be sure to remember (or mark with a Sharpie) the side that faces angled wall pipe. 5. Once the small disk is removed, use a small straight pin or another object to clean out

  2. the small holes. Use plenty of fresh water to help rinse away any debris. Homes with hard water may want to soak the disk in a mixture of half water/half vinegar and then scrub the disk clean. 6. Inspect the disk to make sure each hole is debris-free. Clean again if necessary. 7. Soak shower heads with hard water in the vinegar/water mixture as well. Scrub with a toothbrush to ensure all of the hard water deposits are gone. 8. Rinse the shower head and disk to make sure no debris is left behind. 9. Install the small plastic flow restrictor disk and reattach the shower head to the water pipe. 10. Some shower heads don’t have a plastic disk. If that is the case with yours, buy a new shower head. How To Fix Low Water Pressure In The Shower: Leaking Pipe If you have low water pressure because the angled wall pipe between the wall and the shower head is leaking, you can temporarily fix it by using some thread compound or Teflon tape. Be sure to have a plumber fix the pipe properly and inspect the water line. Leaving a leak in this condition could exacerbate thin pipes elsewhere in the water line and possibly lead to a leak inside the walls. Our servicemen are trained to look for and repair all types of leaks. If you think your shower lines need to be flushed, need a dripping faucet fine-tuned, or the water pressure in your house to be reinstated, call us or visit our website today. Get more information, please visit https://www.deervalleyplumbing.com/

More Related