1 / 11

1.3GHz Large-aperture bpm’s

1.3GHz Large-aperture bpm’s. Jim Crisp Fermilab. Design Information. 1.3GHz bunch spacing /4 = 5.8cm 3 to 5 cm aperture Fit inside a quadrupole ~66nsec rotation period ~86 bunches/turn Turn by turn for 10 turns 1e10 electrons/bunch 2amps average / ~10amps peak. Bpm.

raquel
Download Presentation

1.3GHz Large-aperture bpm’s

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. 1.3GHz Large-aperture bpm’s Jim Crisp Fermilab

  2. Design Information • 1.3GHz bunch spacing • /4 = 5.8cm • 3 to 5 cm aperture • Fit inside a quadrupole • ~66nsec rotation period • ~86 bunches/turn • Turn by turn for 10 turns • 1e10 electrons/bunch • 2amps average / ~10amps peak

  3. Bpm • Suggest 4 plates • 5.8cm long • 1cm wide • ~1/15 of the beam current on each plate • Shorted at one end (not directional) • SMA feedthroughs • Roughly similar plate spacing as Fermi MI bpm’s

  4. Fermilab Main Injector bpm • Measured with wire using 5mm steps • Use simple linear fit along the axis in both directions • 45º rotation would change the shape but not necessarily the error

  5. Linearity error • Error would be ½ as much with 5cm bpm • Using simple linear fit in both directions • Could be reduced with a 2 dimensional fit

  6. Bpm Receiver • Suggest digital receiver • 12bit resolution 210MHz sample rate • 14 samples/turn • 20MHz bandpass filter • ~1 rotation harmonic • Mix 1.3GHz down to ~20MHz • (Requires good quality mixer)

  7. Digital Receiver • 12 bit converter has 64.5db sinad (10.75 bits) • sinad = signal to noise and distortion • noise ~2um distortion ~10um • (Noise improves with N) • 12bit 210MHz adc • 14 samples • 25mm radius bpm • Full scale plate signal • (Xnoise goes like 1/Vplate)

  8. Recycler digital receivers • 14 bit 80MHz adc’s, 120 samples, 63mm radius • each position measured 100 times • Mean is plotted on the left and the standard deviation is on the right

  9. Single bunch position • A single bunch could be used to excite a filter as shown • 210MHz adc sample frequency • 105MHz center frequency • 10MHz bandwidth

  10. Single bunch noise • The wavelet generated from a single bunch has an average voltage 25% of full scale • (Provided the bpm and filter produce a full scale signal for the adc) • The resulting noise and distortion would thus be 4 times larger • Noise ~8um distortion ~40um • About 1.6% of the signal remains after 1 turn • This would allow 1.6% of the previous position to contaminate the subsequent measurement • This could be eliminated by selecting a resonant filter center frequency that puts the previous signal in quadrature • The filters need to be stable and matched • The adc must be synchronized with the beam

  11. Summary • Bunch frequency suggests either buttons or short striplines • The ability to correct for linearity will determine bpm accuracy • Although the electrodes may fit inside a quadrupole, the coaxial feedthroughs likely won’t • Digital receivers are the only way to go • Single bunch measurements are possible with some compromise in noise and accuracy

More Related