1 / 41

Introduction to VLSI Testing

Introduction to VLSI Testing. 李昆忠 Kuen-Jong Lee Dept. of Electrical Engineering National Cheng-Kung University Tainan, Taiwan. Problems to Think. How are you going to test A 32 bit adder A 32 bit counter A 32Mb cache memory A 10 7 -transistor CPU A 10 9 -transistor SOC. OUTLINE.

quinto
Download Presentation

Introduction to VLSI Testing

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Introduction to VLSI Testing 李昆忠 Kuen-Jong Lee Dept. of Electrical Engineering National Cheng-Kung University Tainan, Taiwan

  2. Problems to Think • How are you going to test • A 32 bit adder • A 32 bit counter • A 32Mb cache memory • A 107-transistor CPU • A 109-transistor SOC

  3. OUTLINE • Introduction • Fault modeling • Fault simulation • Test generation • Automatic test pattern generation (ATPG) • Design for testability • Built-in self test • Synthesis for testability • An example

  4. Basic Concept of Testing Testing: To tell whether a circuit is good or bad VDD 0 0 0 0 0/1 0 Related fields Verification:To verify the correctness of a design Diagnosis:To tell the faulty site Reliability: To tell whether a good system will work correctly or not after some time. Debug: To find the faulty site and try to eliminate the fault

  5. Why Studying Testing? • Economics! • Reduce test cost (enhance profit) • Automatic test equipment (ATE) is extremely expensive • Shorten time-to-market • Market dominating or sharing • Guarantee IC quality and reliability Defects detected in Cost Rule of Ten: Cost to detect faulty IC increases by an order of magnitude Wafer 0.01 – 0.1 Packaged chip 0.1 – 1 Board 1 – 10 System 10 – 100 Field 100 – 1000

  6. Principle of Testing Input Patterns Output Response • Testing typically consists of • Applying set of test stimuli (input patterns, test vectors) to inputs of circuit under test (CUT), and • Analyzing output responses • The quality of the tested circuits will depend upon the thoroughness of the test vectors Circuit under Test (CUT) -1011 11-00 -0-1- 01--0 0-101 1-001 0011- -1101 1001- 01-11 Stored Correct Response Comparator Test Result

  7. Importance of testing N = # transistors in a chip p = prob. (a transistor is faulty) Pf = prob. (the chip is faulty) Pf = 1- (1- p) N If p = 10-6 N = 106 Pf = 63.2%

  8. Introduction • Integrated Circuits (ICs) have grown in size and complexity since the late 1950’s • Small Scale Integration (SSI) • Medium Scale Integration (MSI) • Large Scale Integration (LSI) • Very Large Scale Integration (VLSI) • Moore’s Law: scale of ICs doubles every 18 months • Growing size and complexity poses many and new testing challenges VLSI LSI M S I S S I

  9. Importance of Testing • Moore’s Law results from decreasing feature size (dimensions) • from 10s of m to 10s of nm for transistors and interconnecting wires • Operating frequencies have increased from 100KHz to several GHz • Decreasing feature size increases probability of defects during manufacturing process • A single faulty transistor or wire results in faulty IC • Testing required to guarantee fault-free products

  10. Vss Difficulties in Testing • Fault may occur anytime • - Design • - Process • - Package • - Field • Fault may occur at any place Vdd • VLSI circuit are large • - Most problems encountered in testing are NP-complete • I/O access is limited

  11. How to do testing From designer’s point of view: • Circuit modeling • Fault modeling • Logic simulation • Fault simulation • Test generation • Design for test • Built-in self test • Synthesis for testability Modeling ATPG Testable design

  12. Circuit Modeling • Functional model--- logic function • - f(x1,x2,...)=... • - Truth table • Behavioral model--- functional + timing • - f(x1,x2,...)=... , Delay = 10 • Structural model--- collection of interconnected components or elements A E B 1 0 G 1 C 0 D F 0

  13. VDD VDD VDD Levels of Structural Description • Switch level • Circuit level C C4 C1 B C3 C2 E • Gate level • Higher/ System level A E B G C D F

  14. A s-a-1 A s-a-0 B s-a-1 B s-a-0 C s-a-1 C s-a-0 D s-a-1 D s-a-0 E s-a-1 E s-a-0 F s-a-1 F s-a-0 G s-a-1 G s-a-0 14 faults Fault Modeling • The effects of physical defects • Most commonly used fault model: Single stuck-at fault E A B G C D F • Other fault models: • - Break faults, Bridging faults, Transistor stuck-open faults, • Transistor stuck-on faults, Delay faults

  15. # faults detected FC = # faults in fault list Test faults detected FC Fault Coverage (FC) Example: 6 stuck-at faults ( a0,a1,b0,b1,c0,c1 ) 1 1 1 1 0 0 0 0 0 c a b c1 a1,c1 a0,b0,c0 a0,b0,c0,c1 all {(0,0)} {(0,1)} {(1,1)} {(0,0),(1,1)} {(1,0),(0,1),(1,1)} 16.67% 33.33% 50.00% 66.67% 100.00%

  16. Wafer Yield (Chip Yield, Yield) Good Chip Faulty Chip Defects Wafer Wafer yield = 12/22 = 0.55 Wafer yield = 17/22 = 0.77

  17. Shipped Parts IC Fabrication Testing Quality: Defective parts per million (DPM) Yield: Fraction of good parts Rejects Testing and Quality • Quality of shipped parts is a function of yield Y and the test (fault) coverage T • Defect level (DL, reject rate in textbook): fraction of shipped parts that are defective

  18. Yield (Y) Fault Coverage (T) 50% 90% 67,000 75% 90% 28,000 90% 90% 10,000 95% 90% 5,000 99% 90% 1,000 90% 90% 90% 95% 90% 99% 90% 99.9% Defect Level, Yield & Fault Coverage DL: defect level Y: yield T: fault coverage ~ DL = 1 - Y (1-T) DPM (DL) 10,000 5,000 1,000 100

  19. Logic simulation • To determine how a good circuit should work • Given input vectors, determine the normal • circuit response A I C B C A D CC2 CC1 IR G B F B RB IF F E CDE CJE C E H D E

  20. E s.a.0 1/0 1 1 1/0 Fault simulation • To determine the behavior of faulty circuits 1 A 0 B G 0 F C 1 0 D • Given a test vector, determine all faults that • are detected by this test vector. Example: Test vector (1 1) detects { a0, b0, c1} 1 A 0 C B 1

  21. Test generation • Given a fault, identify a test to detect this fault Example: 1 1/0 0 A D 1 1/0 B F 1 C E 0 To detect D s-a-0, D must be set to 1. Thus A=B=1. To propagate fault effect to the primary output E must be 1. Thus C must be 0. Test vector: A=1, B=1, C=0

  22. Automatic Test Pattern Generation • ATPG: Given a circuit, identify a set of test vectors to detect all faults under consideration. Input circuit Form fault list More faults? No Exit Yes Select a fault Fault dropping Test generation Fault simulation

  23. Cannot detect the fault 1 Fault detected 1 Difficulties in Test Generation 1. Reconvergent fanout 0/1 A 0 s-a-1 D 1 0 F B 0/1 1 C E 0

  24. Difficulties in Test Generation (cont.) 2. Sequential test generation PIs POs Combinational part Y J K clk Y CK

  25. Testable Design • Design for testability (DFT) • •ad hoc techniques • Scan design • Boundary Scan • Built-In Self Test (BIST) • Random number generator (RNG) • Signature Analyzer (SA) • Synthesis for Testability

  26. MUX Example of ad hoc Techniques Insert test points T/N

  27. Scan Design Original design Modified design Combinational logic Combinational logic PIs POs PIs POs SO SFF FF SFF FF SFF FF T/N SI

  28. Q,SO DI Q D Q D MUX SI CK CK N/T (SE) Scan Cell Design Q DI Q,SO Q DI DI F F SI F FT F + FT Most cell libraries now have scan cells!

  29. Q D Q D SI SI Scan Register Combinational Circuits Q D Q D SI SI SO SE CLK

  30. Boundary Scan I/O Pad Boundary scan cell Boundary scan path TRST* TDI APPLICATION LOGIC Sout Misc. registers TMS Instruction register T A P BIST register TCK Bypass register Scan register M U X Sin TDO TRST*:Test rest (Optional) TDI: Test data input TD0: Test data output TCK: Test clock TMS: Test mode select

  31. Boundary Scan (Cont.) TRST* TRST* Sout Sout APPLICATION LOGIC APPLICATION LOGIC TDI TDI Misc. registers Misc. registers TMS TMS Instruction register Instruction register T A P T A P BIST register BIST register Bypass register Bypass register TCK TCK Scan register Scan register Sin Sin M U X M U X TDO TDO TRST* TRST* Sout Sout APPLICATION LOGIC APPLICATION LOGIC TDI TDI Misc. registers Misc. registers TMS TMS Instruction register Instruction register T A P T A P BIST register BIST register Bypass register Bypass register TCK TCK Scan register Scan register Sin M U X Sin M U X TDO TDO

  32. Built-In-Self Test (BIST) • Places the job of device testing inside the device itself • Generates its own stimulus and analyzes its own response from system to system circuit under test mux Response Analyzer pattern generator BIST Controller good/fail bistdone biston

  33. F/F Built-In-Self Test (BIST)(Cont.) • Two major tasks • - Test pattern generation • - Test result compaction • Usually implemented by linear feedback • shift register F/F F/F

  34. F/F F/F F/F F/F Random Number Generator (RNG) 0001 1000 0100 0010 1001 1100 0110 1011 0101 1010 1101 1110 1111 0111 0011 0001 (repeat) · · · · 1. Generate “pseudo” random patterns 2. Period is 2n - 1

  35. + + + Signature Analyzer (SA) Input sequence 10101111 (8 bits) 4 1 2 3 5 Z Time Input stream Register contents Output stream 0 1 . . 5 6 7 8 1 0 1 0 1 1 1 1 0 0 0 0 0 Initial state 1 0 1 0 1 1 1 1 0 0 0 0 . . . . 1 0 1 0 1 1 1 1 1 0 0 0 0 1 0 1 1 0 0 0 0 1 0 1 0 0 1 0 1 1 0 1 Quotient Remainder

  36. Signature Analyzer (SA) (cont.) • A LFSR performs polynomial division • Probability of aliasing error = 1/2n (n: # of FFs)

  37. Memory BIST Architecture Before After sys_di Memory Module Memory Module data sys_addr di sys_wen clk q hold_l data addr rst_l test_h si wen so se

  38. clk rst si se Memory BIST Architecture (Cont.) sys_addr di Memory Module sys_di data addr wen sys_wen Algorithm-Based Pattern Generator rst_l clk q compress_h hold_l Compressor test_h so BIST Circuitry

  39. MUX CPU Test Control Architecture Scan_i Scan_o Scan path Scan_en logic rst_l clk Bist control Memory hold_l test_h bist_se bist_so TDO compressor bist decoder int_scan mbist scan decoder bist_si decoder TDI IR TCK TAP Controller TMS

  40. Problems re-thinking • A 32-bit adder --- ATPG • A 32-bit counter --- Design for testability + ATPG • A 32MB Cache memory --- BIST • A 107-transistor CPU --- All test techniques • An SOC

  41. Conclusions • Testing is becoming a major factor in design optimization • Conventionally, the designer often optimize one of the three attributes: speed, area, and power. • At present, a fourth attribute is considered: Testability. • Two major fields in testing • ATPG --- Fault simulation --- Test generation • Testable design --- Design for testability --- Built-in self-test --- Synthesis for testability

More Related