1 / 30

USING THE OXYACETYLENE CUTTING TORCH

USING THE OXYACETYLENE CUTTING TORCH. For EG243 Welding: Pressurizing Lighting Cutting Shutting Down the Airco 9500 Cutting Torch. Procedure, PowerPoint and pictures by Stephen Collins ( scoll@mma.edu ) Demonstration by Robert Giffin

oralee
Download Presentation

USING THE OXYACETYLENE CUTTING TORCH

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. USING THE OXYACETYLENE CUTTING TORCH

  2. For EG243 Welding: Pressurizing Lighting Cutting Shutting Down the Airco 9500 Cutting Torch. Procedure, PowerPoint and pictures by Stephen Collins (scoll@mma.edu) Demonstration by Robert Giffin Click on arrows at top to move to the next page or go back USING THE OXYACETYLENE CUTTING TORCH December 12, 2003

  3. SAFETY • Do not perform this procedure without supervision by an instructor. • Oxyacetylene equipment must be set up in accordance with ANSI/AWS C4.2-90 before beginning. • This procedure is only for the Airco 9500 torch with a #144-1 tip. • Other manufacturers may require different procedures. • Other tip sizes require different pressures (see operator’s manual). • Adequate ventilation must be provided to avoid hazardous accumulation of flammable, explosive, and toxic gases.

  4. PERSONAL SAFETY EQUIPMENT • Wear: • Safety glasses • Cotton clothing (no nylon or polyester) • Long sleeves and pants • Leather boots • Leather welding gloves • #4 Cutting shield (not shown in this picture)

  5. PRESSURIZING • Back out both regulator adjusting “T” handles counterclockwise until they are completely loose

  6. Stand aside. Keep your face away from the gauges. Open the oxygen cylinder valve counterclockwise slowly at first. then all the way, tight up against the back seat. The cylinder pressure gauge should show pressure. PRESSURIZING

  7. Open the torch oxygen valve counterclockwise 1/2 turn. PRESSURIZING

  8. Turn oxygen regulator adjusting “T” handle clockwise. Set oxygen gauge working pressure at 30 psi. Oxygen should now be flowing from the torch tip. PRESSURIZING

  9. Purge 5 sec./50ft of hose. Close the torch oxygen valve clockwise. PRESSURIZING

  10. Stand aside. Keep your face away from the gauges. Open the acetylene cylinder valve counterclockwise until the cylinder gauge shows pressure, then another 1/4 to 1/2 turn counterclockwise but not more than 1 full turn total. PRESSURIZING

  11. Open torch acetylene valve 1/2 turn counterclockwise. PRESSURIZING

  12. Provide adequate ventilation to prevent accumulation of flammable gas. Turn acetylene regulator adjusting “T” handle clockwise. Set acetylene gauge working pressure to 4 psi. Acetylene should now be flowing from the torch tip PRESSURIZING

  13. Provide adequate ventilation to prevent accumulation of flammable gas. Purge 5 sec./50 ft. of hose Close torch acetylene valve. PRESSURIZING

  14. FLASHBACK WARNING: be ready to shut off fuel, then oxygen. Wear shade #4 cutting shield and leather gloves Point torch away from self, cylinders, others, and combustibles Slightly “crack open” the torch acetylene valve LIGHTING

  15. Using only a flint spark lighter, place the lighter near the tip and squeeze. A small, smoky flame should appear at the torch tip. LIGHTING

  16. Open the torch acetylene valve further until the flame is bright and bushy with no smoke, but the flame is still attached closely to the tip. ADJUSTING

  17. Open the torch oxygen valve slowly until the long, white, feathery flame is replaced by sharp white cones at the tip. ADJUSTING

  18. Depress the torch cutting lever completely. While it is depressed, open the torch oxygen valve further as necessary to get clean, sharp, white cones. Blue cones indicate too much oxygen. Release the torch cutting lever. ADJUSTING

  19. Hold the torch handle in one gloved hand, rest the torch tubes on the other. Slide torch out to place tip centered over edge of plate, cone tips just touching the steel. When the steel is red hot, squeeze the cutting lever and slide the torch toward you. CUTTING

  20. Move slowly at first, then more quickly to get a clean cut. CUTTING

  21. SHUTTING DOWN • Shut off the torch oxygen valve quickly, then the torch acetylene valve quickly.

  22. Close the acetylene cylinder valve clockwise all the way. SHUTTING DOWN

  23. Open the torch acetylene valve counterclockwise. Watch both acetylene regulator gauges drop to zero. SHUTTING DOWN

  24. Back out the acetylene regulator adjusting handle counterclockwise until completely loose. SHUTTING DOWN

  25. Close the torch acetylene valve. SHUTTING DOWN

  26. Close the oxygen cylinder valve clockwise all the way. SHUTTING DOWN

  27. Open the torch oxygen valve counterclockwise. Watch both oxygen regulator gauges drop to zero. SHUTTING DOWN

  28. Back out the oxygen regulator adjusting handle counterclockwise until completely loose. SHUTTING DOWN

  29. Close the torch oxygen valve. SHUTTING DOWN

  30. Roll back hoses hang up torch secure oxygen cylinder valve safety cap You can find out more about our welding program at http://weldinglab.mma.edu SHUTTING DOWN

More Related