slide1 n.
Download
Skip this Video
Loading SlideShow in 5 Seconds..
Ginde Pipes Instruction Manual PowerPoint Presentation
Download Presentation
Ginde Pipes Instruction Manual

Loading in 2 Seconds...

play fullscreen
1 / 15

Ginde Pipes Instruction Manual - PowerPoint PPT Presentation


  • 112 Views
  • Uploaded on

Ginde Pipes Instruction Manual. Professional Connection Instructions for certified Ginde Plumbing Contractors. Cutting Ginde Pipes Beveling Ginde Pipes Beveling Ginde Pipes Continued Preparing a Fitting for Crimping Preparing a Fitting for Crimping Continued Crimping a fitting

loader
I am the owner, or an agent authorized to act on behalf of the owner, of the copyrighted work described.
capcha
Download Presentation

PowerPoint Slideshow about 'Ginde Pipes Instruction Manual' - nura


An Image/Link below is provided (as is) to download presentation

Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author.While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server.


- - - - - - - - - - - - - - - - - - - - - - - - - - E N D - - - - - - - - - - - - - - - - - - - - - - - - - -
Presentation Transcript
professional connection instructions for certified ginde plumbing contractors
Professional Connection Instructions for certified Ginde Plumbing Contractors
  • Cutting Ginde Pipes
  • Beveling Ginde Pipes
  • Beveling Ginde Pipes Continued
  • Preparing a Fitting for Crimping
  • Preparing a Fitting for Crimping Continued
  • Crimping a fitting
  • Crimping a fitting Continued
  • Defect check in fitting crimp
  • Pipe Bending Equipment
  • Bending procedure with INNER spring
  • Bending procedure with INNER spring continued
  • Bending procedure with OUTER spring
slide3

By following the prescribed jointing process Ginde Pipes will give you a trouble free installation time and again

  • CUTTING-Cutting Ginde pipe with a Ginde Forfex cutter. See picture1.

Place pipe on flat bed of the Ginde cutter. See picture2

slide4

Cut pipe and get a nice square finish

ROUNDING AND BEVELING-Place Reeming tool into the pipe end to straighten the pipe end for the fitting to be inserted.

slide5

By turning the reamer tool two turns to the left and two turns to the right while pressure is applied inwards .The Gindereamer will round off the Ginde pipe end to make a pouring angle

Pipe end will now have a visible 45 degree bevel on the inside of the pipe

slide6

This is to ensure NO damages to the rubber o-rings on the fitting

SLEEVING- Slide sleeve over reemed pipe end with identification holes at the outside end of the pipe

slide7

FITTING-Press fitting into pipe until pop sound is heard. This to ensure fitting and sleeve is properly connected. Make sure pipe is visible thru sleeve holes.

slide8

COMPRESSING-It is very important to make use of our prescribed Rems crimping tool to complete the pressing of the Ginde fitting onto the Ginde pipe.

Place fitting and pipe into the head gear of the crimping clamp with the white plastic rim flash against the crimping clamp.

slide9

Manipulate the clamp to make its open jaws totally closed.

Open the crimping clamp and take the fitting out. Compression ring marks will be visible.

slide10

A compression tool can be used to check for any default in crimp. Regular checks is advised.

Now you have a finished joint

slide11

INSTRUCTION TO SUCCESSFULLY MAKE A PIPE BEND

  • IT IS OF UTMOST IMPORTANCE TO MAKE USE OF A GINDE PIPE BENDING SPRING.
  • The two pipe bender springs consist of a inner and outer spring. The inner spring is better for bends greater than 90 degrees. This will prevent the pipe not to close up and to ensure normal flow ratios of water in the pipe. It is NOT recommended to bend the pipe back and forth more than two times because this can damage the pipe structure and may cause failures.
slide12

 BENDING INSTRUCTIONS

Slide INNER spring into the pipe to the point that you need to bend

Use both hands and position your two thumbs on the point you want to bend

slide13

Now bend the pipe to your desired position

Pull the spring out. Your bend is complete

slide14

You can also use the outer bending spring in exactly the same way by sliding it over the pipe.

  • For bigger sizes pipe please make use of our Ginde pipe bending kit
slide15

NOTES:

  • It is of utmost importance to use Ginde certified tools
  • The company product guarantee will only be honored if the proper installation procedures was followed by a certified Ginde contractor
  • Ginde pipe can only be used with Ginde fittings and proper installation procedures
  • Ginde Pipe is a NSF certified product
  • Ginde Pipe is a ASTM certified product

Thank You