200-301 VOL1-Question

1. 200-301 Cisco Certified Network Associate (CCNA) VOL1 QUESTION NO: 1 In wireless networking, what are the three main 802.11 frame types? A.Control B.Data C.Version D.Management E.Beacon Answer: A, B, D QUESTION NO: 2 A Computer at a remote site sends a packet to a server located at a Corporate Data Center with a destination IP address of 226.1.5.10. What is the most likely type of traffic that is being used here? A.Traffic sent to the corporate email server to retrieve emails B.Traffic sent to an FTP server to retrieve a file C.Traffic sent to a conferencing server to participate in a companywide video conference. D.Traffic sent to a telephony server so that a voice call can be made using a calling application. Answer: C QUESTION NO: 3 A network Engineer has just configured a new floating static route on router R1 to be used as a backup route to a remote router R2. After making this change, traffic begins taking this new route. What could be a cause for this? A.This is the expected behaviour, when a floating static route is configured traffic will temporarily sent across the newly configured link. B.The floating static route was incorrectly configured with an administrative distance that was too low. C.The floating static route was incorrectly configured with an administrative distance that was too high. D.The floating static route is using a next-hop IP address that is unreachable. Answer: B © Copyright Prep Solutions Limited, All rights reserved

2. QUESTION NO: 4 In a small EIGRP network, routers R1 and R2 are EIGRP neighbors and have been configured with default values. R1 and R2 are connected via two different 100 MB links. What must be configured on these two routers for traffic to load balance over these two links? A.R1 and R2 must have variance configured the EIGRP process. B.Variance must be configured on router R1 only. C.EIGRP load balancing must be enabled under the EIGRP process of routers R1 and R2. D.Nothing needs to be configured, the traffic will load balance automatically. Answer: D QUESTION NO: 5 A new network administrator has just been hired to manage an existing multi-vendor network consisting of numerous devices. There is currently no network documentation, and he has been tasked with getting a better understanding of the physical topology of this network. Which protocol should the network administrator enable to gain visibility into the physical connections that are used be-tween these network devices? A.LLDP B.CDP C.BFD D.STP Answer: A QUESTION NO: 6 You need to design an IP addressing scheme for a new network that should be routable internally only, and not be reachable from the Internet. The network consists of one flat network, and should accommodate up to 150 hosts. Wasting of IP addresses should be avoided. Which of the following would be the best subnet to use? A.11.1.1.0/24 B.192.168.1.0/25 C.172.30.1.0/24 D.172.33.1.0/24 Answer: C © Copyright Prep Solutions Limited, All rights reserved

3. QUESTION NO: 7 Which of the following are the core components of an 802.1x architecture? (Choose three) A.Authenticator B.Supplicant C.Wireless Lan Controller D.Authentication server E.LDAP server Answer: A, B, D QUESTION NO: 8 A new Wireless LAN Controller was just purchased and you need to connect to the console to begin the initial configuration. What are the terminal emulator settings that should be used for this connec-tion? A. •9600 baud •8 data bits •1 stop bit •No parity •No hardware flow control B. • • • • • 9600 baud 16 data bits no stop bit No parity No hardware flow control C. • • • • • 19200 baud 8 data bits no stop bit parity No hardware flow control D. • • • 9600 baud 16 data bits stop bit © Copyright Prep Solutions Limited, All rights reserved

4. • • No parity hardware flow control Answer: A Reference: https://www.cisco.com/c/en/us/support/docs/wireless/4400-series-wireless-lan- controllers/69719-wlc-lwap-config.html QUESTION NO: 9 Refer to the following network: Host PC1 is unable to ping Server 1. Traceroutes show that the packets are load balanced to Router 3 and Router 4 before timing out. What is the most like reason for this? A.PC1 has an incorrect default gateway set. B.Load balancing between Router 2 and routers Router 3 and Router 4 are causing issues. C.Server 1 has an incorrect default gateway set. D.Router 2 is blocking ICMP via an ACL. Answer: C © Copyright Prep Solutions Limited, All rights reserved

5. QUESTION NO: 10 Refer to the following network: Regarding traffic between PC1 and Server 1 in this network, between which two devices is a 32- bit header added to the packet between the layer 2 header and the IP packet? A.Between Router 1 and Router 2 B.Between Switch 2 and Routers 3 and 4. C.Between Switch 3 and Server 1. D.Between Switch 1 and Router 1. Answer: A QUESTION NO: 11 A network administrator performs the following on router R1: R1# configure terminal Enter configuration commands, one per line. End with CNTL/Z. R1(config)# interface gig 0/0 R1(config-if)# switchport R1(config-if)# switchport mode trunk © Copyright Prep Solutions Limited, All rights reserved

6. R1(config-if)# switchport port-security Based on this, what will be the resulting violation mode when the “show port-security” command is issued for this interface? A.Protect B.Restrict C.Shutdown D.On Answer: C QUESTION NO: 12 The login password for a router has been forgotten and needs to be reset. Which configuration register value must be set in the router in order to cause the router to boot up without requiring a password? A.0x2102 B.0x2042 C.0x2242 D.0x2142 Answer: D QUESTION NO: 13 An engineer needs to configure router R1 to send log messages of severity level notifications and lower syslog server at 10.22.22.55. How can this be achieved? A.R1(config)# logging 10.22.22.55/24 R1(config)# logging level 4 B.R1(config)# logging 10.22.22.55 R1(config)# logging trap 5 C.R1(config)# logging 10.22.22.55 R1(config)# logging level 5 D.R1(config)# logging 10.22.22.55 R1(config)# logging trap 4 Answer: B QUESTION NO: 14 © Copyright Prep Solutions Limited, All rights reserved

7. Which of the following describe the valid port states in the operation of the 802.1D protocol? A.Disabled, Discarding, Learning, Forwarding B.Disabled, Blocking, Listening, Learning, Forwarding C.Discarding, Learning, Forwarding D.Enabled, Blocking, Listening, Learning, Forwarding Answer: B QUESTION NO: 15 Which of the following are the three components of the Three-tier Hierarchical Networking Model used in the classical Cisco networks design? (Choose three) A.Distribution B.Core C.Spoke D.Access E.Leaf F.Spoke Answer: A, B, D QUESTION NO: 16 Within the Cisco Wireless LAN Controller and lightweight AP QoS configuration profile, which level should be selected for voice over wireless? A.Platinum B.Bronze C.Gold D.Silver Answer: A QUESTION NO: 17 In IPv4, the Address Resolution Protocol (ARP) is used to find the layer 2 MAC address associated with a layer 3 IP address. How is this same functionality done in IPv6? A.IPv6 ARP B.Link Local addressing C.Anycast addressing © Copyright Prep Solutions Limited, All rights reserved

8. D.Neighbor Discovery Protocol Answer: D QUESTION NO: 18 While configuring a router, you accidentally mistype a command and the following happens: R1#conffig Translating "conffig"...domain server (255.255.255.255) % Unknown command or computer name, or unable to find computer address You want to avoid this behavior, but don’t have a valid DNS server that can be used to resolve host names to IP addresses. What should be configured to do this? A.R1(config)#no ip domain-lookup B.R1(config)#domain-lookup disable C.R1(config)#ip domain-name none D.R1(config)#no dns-lookup Answer: A QUESTION NO: 19 What benefit does the Simultaneous Authentication of Equals (SAE) perform in the WPA3 authentication method? A.SAE adds a step to a password connection that makes it impossible for brute force attackers to expose the password B.SAE creates an encryption algorithm for the password during transit of the data C.SAE negotiates with the server and jumbles up a password so that brute force attackers cannot figure it out. D.SAE uses CCM 192-bit encryption to encrypt passphrase during the data transit Answer: A QUESTION NO: 20 Which of the following are First Hop Redundancy protocols based on industry standards and work in a multi-vendor network environment? (Choose all that apply) A.HSRP B.GLBP © Copyright Prep Solutions Limited, All rights reserved

9. C.VRRP D.PVSTP Answer: B, C © Copyright Prep Solutions Limited, All rights reserved