1 / 41

PGY-1 CURRICULUM Basic Orthopaedic Skills

PGY-1 CURRICULUM Basic Orthopaedic Skills. Indiana University School Medicine Department of Orthopaedic Surgery July, 2013. GOALS. Understand the indications for percutaneous pinning (PP) of fractures (fx)

mitch
Download Presentation

PGY-1 CURRICULUM Basic Orthopaedic Skills

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. PGY-1 CURRICULUMBasic Orthopaedic Skills • Indiana University School Medicine • Department of Orthopaedic Surgery • July, 2013

  2. GOALS • Understand the indications for percutaneous pinning (PP) of fractures (fx) • Understand the indications for damage control orthopaedics and stabilization with external fixation (EF) devices • Understand the complications of EF and PP devices • Demonstrate the ability to use the small battery drive • Demonstrate the ability to place K-wires across a fx • Demonstrate the ability to place a simple EF construct

  3. PERCUTANEOUS PINNING OF FRACTURES • The most common fx using percutaneous pinning is the pediatric supracondylar humerus fracture (types II and III) • It is the most common operative procedure in pediatric fxs • Jan 2004 – Dec 2011 – 297 cases of the most severe type III SCH fx rx’ed at Riley

  4. PEDIATRIC SCH FX • Type I – non displaced • Type II – posterior cortex intact • Type III – completely displaced • All type II and IIIs rx’ed with CRPP

  5. TODAY – LEARN HOW TO PIN THE FX AFTER REDUCTION • Learn to use the battery driver • Understand K wire and Steinmann pin size • Understand the best mechanical configuration for CRPP • Understand the concerns for cross pinning • Demonstrate appropriate skill in pinning

  6. K-WIRES AND STEINMANN PINS • Are the same , differentiated by size • K wires – 0.028" (0.7mm) diameter 0.035" (0.9mm) diameter • 0.045" (1.1mm) diameter • 0.054" (1.4mm) diameter • 0.062" (1.6mm) diameter • Steinmann pins – • Range from 5/64” (2.0mm) to3/16” (4.8mm) in increments of 1/64”

  7. K-WIRES AND STEINMANN PINS • Trocar or diamond end • Smooth or threaded • Single or double

  8. GENERAL CONCEPTS WITH PERCUTANEOUS FX PINNING • The drill is typically battery powered • Can use either quick release or Jacob’s chuck • For PP of fx using with smaller pins I recommend a quick release chuck

  9. DRILL CHUCKS • Jacob’s chuck – the standard wood shop chuck using a key to tighten it • Quick release – the chuck grabs the wire by simply squeezing the handle

  10. PLACE THE PIN IN THE CHUCK • With quick release make sure the number of “dots” is the appropriate one for the pin size selected • Assure the quick release is working properly and make sure it is powered before even starting the fixation!!!

  11. START THE PIN FIXATION • Start perpendicular to the bone • When necessary, begin to angle the drill/wire after entering the bone – in a gradual manner • Do not bend the pin!

  12. RADIOGRAPHIC ASSESSMENT • Start the pin under radiographic control to ensure appropriate direction • Monitor frequently - both AP and lateral • As you acquire more experience, the amount of imaging will become less

  13. PIN CONFIGURATION • Biomechanically, cross pin fixation better • However it is associated with a significant increase in iatrogenic ulnar nerve injury – 1 in every 28 pts rx with cross pins will have an iatrogenic ulnar N injury!! • Multiple pins using lateral entry are clinically equal to cross pin configuration • Cross pinning should be used in only the most unstable situation!!!!

  14. PIN CONFIGURATIONS

  15. IDEAL PINNING

  16. TYPE III SCH FXPerfect Pinning! • All pins parallel/divergent • All pins engage both cortices on both AP and lateral views • No cross pins!!

  17. NUMBER OF PINS • For lateral entry pinning 3 is the typical number • However do not be afraid to use the blow gun technique – 4 or 5 pins • Remember that an iatrogenic ulnar N injury is a significant event!

  18. AFTER FIXATION • Extend the elbow to assess the carrying angle / cubitus varus • Assess the stability of the fixation under real time flouroscopy with flexion / extension of the elbow

  19. EXTERNAL FIXATOR - TIBIA • Today - • Identify the components in the large ex fix set • Review the steps for the assembly of a frame • Make sense of the “tinker toys”

  20. EXTERNAL FIXATORIndications • Trauma • Open Fractures • Severe soft tissue injury • Comminution • Bone loss • Temporizing or Definitive

  21. DAMAGE CONTROL ORTHOPAEDICS • Applies to the polytraumatized patient • 3 main stages • Early temporary stabilization of unstable fxs, control of hemorrhage, and decompression intracranial lesion • Resuscitation of pt in ICU and optimization • Delayed definitive management of fxs

  22. DAMAGE CONTROL ORTHOPAEDICS

  23. EXTERNAL FIXATOR Advantages • Simplicity and ease of application • Minimal blood loss • Adjustability after surgery • Access for wound management

  24. EXTERNAL FIXATORDisadvantages • Anatomic structures at risk (Safe Zones) • Pin/Wire site infections • Joint contractures • Prolonged time to bony healing

  25. EXTERNAL FIXATOR - TIBIA • Simple: • Clamps • Bars • Pins

  26. TERMINOLOGY • Bars, Rods and Tubes are used interchangeably • bars & rods are solid • tubes are hollow • Pins & Schanz Screws • same

  27. EX FIX CLAMPS • Connects pins to rods

  28. EX FIX CLAMPS • Combination clamps – connects • Pins to rods • Rods to rods

  29. EX FIX PINS/CLAMPS • Large clamps accommodate 4.0mm to 6.0mm Schanz Screws 4.0 mm for Small Ex Fix 4.5 & 5.0 mm for tibia and pelvis 6.0 mm for femur and large distractor

  30. INSERTING PINS • Select site under flouroscopy • Small longitudinal incision • Hemostat down to bone • Then use the trocar and sleeves • Drilling and pin tract/insertion should be perpendicular to bone

  31. SAFETY FACTORS • Pin/Wire should not • be in the fracture • When drilling go slow as not to burn the bone

  32. STABILITY FACTORS Pin/Wire Location Maximal pin span More pins distribute forces and increase construct stiffness

  33. STABILITY FACTORS • Lower Bone-Rod distance increases stiffness • In-line stacking • increases stiffness • Second sidebar at 90o to first increases stiffness

  34. STABILITY FACTORS • Pin/Wire Size • Torsional strength proportional to its radius4 • Pin core diameter • < • 1/3 bone diameter

  35. STABILITY FACTORS • Insertion Technique • Thread-Shank junction • is weakest point • Insert pin shank to • proximal cortex • (2x increased stiffness) • (threads = bone width) • Off plane pin insertion

  36. INSERTING PINS • To insert pins: • Trocar & 2 sleeves • 3.5mm drill bit • Irrigate to prevent heat & pin loosening ! 3.5mm inner sleeve for 3.5mm drill bit 5.0mm outer sleeve for Schanz screw Trocar

  37. INSERTING PINS • Chuck with T handle through outer sleeve • Advance to proper depth, just engaging opposite cortex – both a feel and radiographically confirmed

  38. ADDING RODS/CLAMPS Use 11mm cannulated socket wrench or ratchet wrench Need 2 of each for surgeon and assistant Then reduce fracture - flouroscopic control

  39. PIN CUTTERS AND PROTECTORS • Protects contralateral extremity and allows patient movement

  40. Spanning External Fixators • Portable Traction • Span intra-articular fracture • Aide reduction through ligamentotaxis

  41. THE END

More Related