1 / 12

Radiopharmaceutical Production

Radiopharmaceutical Production. Target Foil Characteristics . STOP. In order to separate the target material from the vacuum of the cyclotron, a thin metal foil is often used on the front of a cyclotron target.

mingan
Download Presentation

Radiopharmaceutical Production

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Radiopharmaceutical Production Target Foil Characteristics STOP

  2. In order to separate the target material from the vacuum of the cyclotron, a thin metal foil is often used on the front of a cyclotron target. This metal foil will attenuate the beam and therefore thin is better. On the other hand, the foil must be strong enough to withstand the pressure differential between the cyclotron vacuum and the target material. Contents Thermal Conductivity Tensile Strength Chemical Reactivity Energy Loss in the Foil Activation of Foils Target Foils STOP

  3. Thermal Conductivity The thermal conductivity of the foil will determine the rate at which heat will be removed from the foil. If the foil is also cooled by either forced or free convection on the front surface (not in a vacuum), the heat deposited by the beam will be removed by a combination of these two processes. Foil materials such as aluminum are very good thermal conductors. The thickness of the foil will also determine the amount of heat which can be removed by this process as is evident from examining the equation for heat transfer by conduction. A list of some common foil materials and the thermal conductivity for each is given in the Table on the next page.

  4. Thermal Conductivity Physical and Thermal Properties of some Foil Materials

  5. As an illustration of the effects that convective cooling can have on the temperature of a foil, a simulation has been carried out and is presented in the Table. Increasing the film coefficient (h) decreases the temperature of the foil so that it can withstand higher beam currents. Havar was chosen as an example because the thermal conductivity is low which means that convective cooling must be the primary means of heat removal. (See the section on heat transfer) The blanks in the table means the temperature was above the melting point of Havar at 1493°C. Thermal Conductivity

  6. Tensile Strength • Another important parameter is the tensile strength of the foil. The stress placed on a circular membrane in a clamping flange with radiused edges is given by the relation: • where φ = stress placed on the membrane • P = pressure (psi) • E = Young's Modulus (psi) • a = radius of the foil (cm.) • h = thickness of the foil (cm.) • If the stress on the foil exceeds the tensile strength of the foil, then the foil will burst. This will usually occur in the center of the foil since this is where the maximum stress occurs on a well clamped foil (i.e. a clamping flange whose edges have been radiused). Some values for the tensile strength of some common foil materials are given in the table on the Physical and Thermal Properties of some Foil Materials

  7. The temperature dependence of the yield strength can be quite different depending on the material. The yield strength versus stress curves for several materials is given in the figure below. It can be clearly seen that for most materials, the yield strength decreases rapidly with increasing temperature. This is not the case however with certain types of stainless steels where the yield strength increases slightly before decreasing with increasing temperature. Thus, the pressure in the target and the temperature during irradiation will determine the thickness of the foil which will be necessary to withstand the stress. Tensile Strength and Temperature

  8. Chemical Reactivity The next important characteristic of the foil is the chemical reactivity. This depends on the target material. In nitrogen targets, the foil is often aluminum since this material is chemically inert to the nitrogen gas and to the carbon-11 products produced. Aluminum cannot be used in a target for the production of fluorine-18 from oxygen-18 water since the fluorine interacts with the aluminum and it is very difficult to remove the fluorine-18 from the target. An aluminum target can be used for gaseous fluorine-18 production since the surface can be made non-reactive by exposure to fluorine gas at low concentrations. It is necessary to consider the chemical combination of the foil material with the target material not only at room temperature but also at elevated temperatures since this is often the situation inside the target. Each target must be considered on a case by case basis and there are no rules other than those of chemistry.

  9. Energy Loss in the Foil The energy loss in the foil is another consideration, since this will have an impact on the beam energy incident on the target material and also on the heat which is deposited in the foil. The energy degradation relates to the stopping power of the material as was calculated in the section on physics. The ideal is to have a foil as thin as possible to withstand the pressure in the target so that the minimum amount of energy is deposited in the foil. An exception to this rule comes up when it is necessary to reduce the beam energy in order to have the energy incident on the target material at an optimum energy with respect to the cross-section of the desired nuclear reaction.

  10. Activation of Foils Another consideration is the radioactivation of the target foils, since this will often determine how radioactive the target will be. All target foils need to be replaced at fairly frequent intervals and this can result in a radiation dose to the person working on the target. Aluminum is often the material of choice in this regard because there are very few long lived activities formed in the foil. Nickel alloys and steels, which must be used for chemical inertness in certain situations, are perhaps the worst commonly used materials with respect to activation since these metals often have several long-lived activities associated with them. One of the most common foils used for cyclotron targets is Havar and it has many activation products. A gamma spectrum is shown on the next slide.

  11. Gamma spectrum from a Havar foil after 80 hours of irradiation Activation of Foils O’Donnell et al ApplRadiatIsot, 2004 Dose rates to the skin from handling these foils can be more than 20 mSv/hr VivekManickam, et al Health Phys.96(Supplement 1):S37–S42;2009

  12. Return to Main Menu

More Related