1 / 9

Temperature Dependence of EMF

Temperature Dependence of EMF. Where thermodyamics and electrochemistry meet. Objective: Determine the ΔG, ΔH and ΔS of the oxidation- reduction reaction for the cell: Ag(s) | AgCl(s) || Hg 2 Cl 2 (s) | Hg(l) This cell has the half-reactions:.

Download Presentation

Temperature Dependence of EMF

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Temperature Dependence of EMF Where thermodyamics and electrochemistry meet.

  2. Objective: Determine the ΔG, ΔH and ΔS of the oxidation- reduction reaction for the cell: Ag(s) | AgCl(s) || Hg2Cl2(s) | Hg(l) This cell has the half-reactions: Anode (oxidation): 2Ag(s) = 2AgCl(s) + 2e- Cathode (reduction): 2e- + Hg2Cl2(s) = 2Hg(l) Net: 2Ag(s) + Hg2Cl2(s) = 2AgCl(s) + 2Hg(s) All at atmospheric pressure and some temperature T.

  3. Physical Principles For a reversibly operating electrochemical cell operating at constant temperature and pressure and doing no other work: ΔG = - NF E Where N is the number of Faradays passing through the cell, F is the Faraday constant and E is the emf of the cell. From the Gibbs-Helmholz Equation:

  4. Substituting for ΔG gives: With both ΔG and ΔS determined, ΔH can then be found: ΔH = ΔG + TΔS

  5. Experiment • EMF is measured by a high-impedance, solid-state voltmeter • The AgCl is deposited onto a silver strip • Clean Ag strip with sandpaper and rinsed with deionized water • Strip is place in beaker of 1M HCl and AgCl is electrolytically deposited ( use 1.5V dry cell) • Stop when shiny strip is darkened • Let sit for 5 min, then rinse and place in H-cell as quickly as possible (avoid drying of the coating) • Hg2Cl2 is “floated” on a pool of Hg

  6. Cell must be clean. An obviously dirty cell will not give acceptable results. • KCl solution in cell must be fresh • Water to make solution must be boiled to remove dissolved oxygen • Be sure connectors such as alligator clips are not corroded. If corrosion is present then “polish” using sandpaper • Be sure wires are firmly connect to clips

  7. Place cell in bath and wait usually 10-15 minutes to reach equilibrium. • Measure emf (voltage) until there is no drift in value and it is essentially constant • Measure emf of cell for at least four different temperatures in the range of 0o-35o Celsius. • Start at low temperature, go to high, then go from high to low. • Use the same voltmeter to make the measurements

  8. Calculations • Plot the cell emf against the absolute temperature. • Using a linear-least squares plot determine the slope (E / T )p and the best value of E . • Use E to calculate ΔG • Use the slope, (E / T )p , to calculate ΔS • Use the computed values of ΔG and ΔS to calculate ΔH

More Related