1 / 14

Permanent Head Gasket & Block Repair w/Nanotechnology, 32 Fl Oz

Permanent Head Gasket & Block Repair w/Nanotechnology, 32 Fl Oz. Block and Radiator Seal Permanently seals small holes and cracks, repairing:. Engine blocks Cylinder heads Radiators Heater cores Cooling passages Head gaskets Water Jackets.

Download Presentation

Permanent Head Gasket & Block Repair w/Nanotechnology, 32 Fl Oz

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Permanent Head Gasket & Block Repair w/Nanotechnology, 32 Fl Oz • Block and Radiator Seal • Permanently seals small holes and cracks, repairing: • Engine blocks • Cylinder heads • Radiators • Heater cores • Cooling passages • Head gaskets • Water Jackets

  2. Permanent Head Gasket & Block Repair w/Nanotechnology, 32 Fl Oz Nanotechnology Block Seal seeks out cracks or small holes in the engine block, radiator, head gasket, freeze plugs and heater core.

  3. Permanent Head Gasket & Block Repair w/Nanotechnology, 32 Fl Oz Once the crack or hole is located, Nanotechnology Block Seal, mixed with water, is forced in from the pressure of the cooling system. Nanotechnology Block Seal is hardened as oxygen passes over the crack forming a permanent molecular bond that’s as strong as steel.

  4. Permanent Head Gasket & Block Repair w/Nanotechnology, 32 Fl Oz How to Use: Example: 1985 Ford Fairmont 3.8L V-6 136K Miles The ProblemInternal coolant leak DiagnosisCracked head gasket Mechanic’s Estimates$800 - $1,400 Alternate Repair MethodInstall K&W Block Seal

  5. Permanent Head Gasket & Block Repair w/Nanotechnology, 32 Fl Oz Preparation • Park vehicle in a spot where it can sit for at least 24 hours. • Products needed: Nanotechnology Block Seal, Radiator Flush and Radiator Anti-Rust. • Other products & tools required: Antifreeze, drain pan and basic hand tools.

  6. Nanotechnology Block Seal Step 1 • Drain antifreeze into drain pan Nanotechnology Block Seal cannot be added to coolant because it will solidify. Tip: If you plan on reusing current antifreeze, drain into a clean pan. It is suggested that you use new antifreeze.

  7. Nanotechnology Block Seal Step 2 • Flush cooling system Why? To remove scale, rust and corrosion. This will aid the sealing process and clean the cooling system. Tip: Using a “back-flush” kit is the most effective method of flushing.

  8. Nanotechnology Block Seal Step 2 (repeat) • Flush, Flush, Flush! • This may be the most important step. Flush the cooling system until the water is clear and there is no antifreeze present. • Turn on the heater and defroster while vehicle is running. This will ensure that the thermostat is open resulting in faster warm-up time. If possible, remove the thermostat and replace after leak has been repaired. • Tip: If you are experiencing an internal coolant leak (compression leak), remove and check spark plugs for corrosion or fluid appearance. You may also run a compression test. Upon determining the affected cylinder(s) remove the spark plug and disable the fuel injection before the next step.

  9. Nanotechnology Block Seal Step 3 • Mix Nanotechnology Block Seal with water • In a separate container, mix entire container of Nanotechnology Block Seal with 3 quarts of clean warm tap water. Shake/mix the solution before adding to the empty cooling system. • Use a clean plastic milk jug or other container to mix Nanotechnology Block Seal and water.

  10. Nanotechnology Block Seal Step 4 • Add Nanotechnology Block Seal mixture • Pour entire Nanotechnology Block Seal mixture into cooling system. • Immediately start the vehicle, top-off with water, and replace the radiator cap and let the vehicle idle for a minimum of 20 to 30 minutes. If vehicle overheats, turn off vehicle and let temperature return to normal and restart for remaining time frame. • If the thermostat has not been removed, turning on the heat and defrost will ensure the thermostat opens

  11. Nanotechnology Block Seal Step 5 • Let vehicle cool • After vehicle is cool, remove radiator cap and drain cooling system Tip: There is not a specific time frame for cooling. You may drain cooling system when you feel comfortable removing the fluid.

  12. Nanotechnology Block Seal Step 6 • Drain and Cure • Remove radiator cap and open all drain cocks to allow air to circulate in the cooling system. Removing the lower radiator hose will help in allowing more air into the coolant system • Let empty cooling system dry for a minimum of 12 hours. Tip: Block Seal needs air to cure and form a permanent bond, the longer it can dry the better the adhesion.

  13. Nanotechnology Block Seal Step 7 • Flush and Add coolant • After drying time has elapsed, flush coolant system until clear and fill with a 50/50 mix of antifreeze & water (You may add anti-rust or other additives if desired). • Let vehicle idle until hot. • The leak has been repaired. • Reinstall thermostat if it was removed during the process. • Change oil and filter if oil is contaminated. A engine oil flush is recommended if the oil is extremely dirty. • Check coolant level frequently over the next 100 miles.

  14. Results LEAK REPAIRED! Cost Retail K&W Nanotechnology $20.00 Block Seal CRC Radiator Flush $1.99 Antifreeze (x2) $9.98 CRC Anti-Rust $1.99 Drain Pan $4.99 Total $25.64 Estimate to Repair Vehicle $800 to $1,400 SAVINGS $774 TO $1,374!!!!

More Related