1 / 17

Development of Burr-free Meso Punching System

Development of Burr-free Meso Punching System. Byeong Hee Kim Division of Mechanical Engineering and Mechatronics, Kangwon National University. Contents. Objectives Burr formation mechanism Meso punching system Auto-aligning algorithms Experimental results and discussion Conclusion.

lazar
Download Presentation

Development of Burr-free Meso Punching System

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Development of Burr-free Meso Punching System Byeong Hee Kim Division of Mechanical Engineering and Mechatronics, Kangwon National University pmlab.kangwon.ac.kr

  2. Contents • Objectives • Burr formation mechanism • Meso punching system • Auto-aligning algorithms • Experimental results and discussion • Conclusion pmlab.kangwon.ac.kr

  3. Monitoring system Punching system Controller Meso Deburring M/C Objectives Meso Punching System Punching system + Deburring M/C Modules of Desktop factory pmlab.kangwon.ac.kr

  4. Rollover Burnish zone Fracture zone 2nd burnish zone Burr Depth of the crack penetration Mechanism of burr formation • The crack initiates from the top initial indent point (A) and connects to the bottom initial indent point (B). pmlab.kangwon.ac.kr

  5. Troubles caused by burrs • Reduce the quality of machined (sheared) parts • Cause interference, jamming and misalignment during assembly procedures • Safety hazard to personnel • Hard to predict • Hard to avoid • De-burring is time-consuming and costly pmlab.kangwon.ac.kr

  6. insulatedpunch-die interface laser aligner pneumatic punching head sheet metal feeding system micro aligning stage Meso -punching machine pmlab.kangwon.ac.kr

  7. System operation pmlab.kangwon.ac.kr

  8. Initial punch-die alignment procedure Steps • X-Y table moves toward -X until the punch contacts the die. • Table goes backward to the opposite direction before the new contact signal is detected. • Distance between the contact points can be calculated by using electric pulse signals. • Table moves to the center of both points. pmlab.kangwon.ac.kr

  9. Initial alignment example pmlab.kangwon.ac.kr

  10. Principle of in-situ alignment • Step 1 Sheet metal is fed to the designated position by the feeding actuator. • Step 2 Burr heights at the position ① and ② are measured by the laser probe. • Step 3 Difference between burrs heights is calculated • Step 4 Table is moved to the right or the left minutely according to the value of the difference. pmlab.kangwon.ac.kr

  11. Spot size is reduced to1~2㎛ Spot size reduction • Introducing achromatic doublet lens • Burr height pmlab.kangwon.ac.kr

  12. Experimental Conditions pmlab.kangwon.ac.kr

  13. Effect of initial alignment Brass t = 0.05 mm c = 10 mm 3 × 3 mm square hole Aluminum t = 0.2 mm c = 10 mm Misaligned Aligned pmlab.kangwon.ac.kr

  14. Burr height w.r.t. clearance pmlab.kangwon.ac.kr

  15. 30mm 6mm Effect of in-situ alignment (copper) Misaligned t = 50 mm c = 10 mm Aligned t = 50 mm c = 10 mm SEM photo Laser output pmlab.kangwon.ac.kr

  16. Ultrasonic deburring conventional method reversal flow resistance method Deburring machine Before deburring After deburring pmlab.kangwon.ac.kr

  17. Conclusion • We developed the precision meso-punching system and introduced two kinds of punch-die auto aligning methods : the punch-die contact sensing method and the in-situ self-aligning method • By reducing the spot size of the laser under 2 micrometers by the achromatic lens system, we can get the more accurate dimensional information of the burr • The burrs formed during the punching process can be uniformized and minimized by using aligning methods. • Novel deburring method was developed for almost burr-free parts. pmlab.kangwon.ac.kr

More Related