1 / 11

CIMExcel Software Inc. Slide 1

Optimal Mineral Processing Control (AMPC). Increases Stability and Reduces Variability. Increases Ore Throughput and Metal Recovery. Increased Throughput 3 - 5 %. Increased Recovery 1 - 3 %. SAG / AG Mill Control and Optimization. Cyclone Scheduling and Optimization.

lars
Download Presentation

CIMExcel Software Inc. Slide 1

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Optimal Mineral Processing Control (AMPC) • Increases Stability and Reduces Variability. • Increases Ore Throughput and Metal Recovery. • Increased Throughput 3 - 5 % • Increased Recovery 1 - 3 % • SAG / AG Mill Control and Optimization. • Cyclone Scheduling and Optimization. • Flotation Control and Optimization. • Integrated Conventional and Advanced Control. CIMExcel Software Inc. Slide 1

  2. OMPC - Integrated Conventional and Advanced Control • Conventional Control: • Feeder Speed • SAG / AG Mill Dual Power - Load Control • SAG / AG Mill Speed • SAG / AG Mill Water Ratio • SAG / AG Mill Water Addition • SAG / AG Mill Additives • SFPB and CFPB Level • Cyclone - Underflow and Overflow Water Addition • Ball Mill Additives • Flotation - Air Flow and Reagents Flow • Lube Systems Temperature • Advanced Control: • Stockpile Ore Size Distribution - Feeder Modal Control • SAG / AG Feedrate, Water Ratio, and Mill Speed • SFPB and CFPB Level • Lube Systems Temperature • Cyclone Scheduling • Cyclone - Overflow Solids • Flotation - Air Flow and Reagents Flow OMPC CIMExcel Software Inc. Slide 2

  3. OMPC - SAG / AG Mills - Advanced Control • Stockpile Ore Size Distribution - Feeder Modal Control • Ore Quality Analysis and Feedforward Control • Advanced Hill-Climbing Optimization • Water Ratio Optimization • Speed Optimization • Ore Load Control Mode • Feedrate and Power Constraints Mode • Grinding Rate Model • Continuous Response Identification and Learning OMPC CIMExcel Software Inc. Slide 3

  4. OMPC - Ore Quality Feedforward Control The Relative Grinding Time, the current steel load, and the time from the last lifter/liner rebuild are used to determine the Maximum Feedrate. OMPC uses the Maximum Feedrate value as the remote setpoint to the Feedrate Control Loop. The particle size distributions for the relative grinding time (RGT = 0.8, 1.0, 1.2) are determined from belt cut testing and correlation with the Ore Size Analyzer data. The realtime Ore Size Analyzer data is used to determine the current value of the Relative Grinding Time. OMPC CIMExcel Software Inc. Slide 4

  5. OMPC - Ore Quality Feedforward Control In the above, A-line and B-line are fed from the same stockpile. A-line has Ore Quality Feedforward enabled and averages 962 Tph. B-line has conventional Power-Load Control enabled and averages 652 Tph. There is a significant performance improvement with OMPC Ore Quality Feedforward Control. OMPC CIMExcel Software Inc. Slide 5

  6. OMPC - Advanced Hill-Climbing Optimization OMPC CIMExcel Software Inc. Slide 6

  7. OMPC - Increased Ore Throughput ~ 5% OMPC CIMExcel Software Inc. Slide 7

  8. Conventional Power-Load Control Loop For the conventional power-load control loop for the above primary mill power and load performance curves, the operator needs to enter a water ratio value (0.65), a power setpoint value (6700 kw), a load setpoint value (660 psi), a high power feeder cutback value (7100 kw), and a high load feeder cutback value (675 psi). These values are critical and determine the throughput and the operating stability of the primary mill. If feeder cutbacks are encountered - the operator will lower these values, if no feeder cutbacks have been encountered - the operator will raise these values. OMPC CIMExcel Software Inc. Slide 8

  9. Conventional Power-Load Control Loop In the above, A-line and B-line are fed from the same stockpile with moderately varying ore quality. A-line has OMPC - Ore Quality Feedforward Control active and averages 962 Tph. B-line has Conventional Power-Load Control active and averages 652 Tph. There is a significant performance improvement with OMPC Ore Quality Feedforward Control. OMPC CIMExcel Software Inc. Slide 9

  10. OMPC – Recovery Optimization • Cyclone Scheduling and Optimization • Flotation Solids Control and Optimization • Flotation (Air and Reagents) Feedforward Control OMPC CIMExcel Software Inc. Slide 10

  11. OMPC - Increased Metal Recovery ~ 2 % A1 and A2 Ball Mill - Cyclones - Flotation sides are identical and are fed equally from the same primary mill with the same particle size distributions. A1-side has OMPC - Cyclone Scheduling turned on, A2-side does not. Both sides have OF Density Optimization, Feedforward Air Ratio, and Reagents Flow Ratio turned on. A1-side averages 89.8 % recovery efficiency. A2-side averages 87.6 % recovery efficiency. OMPC CIMExcel Software Inc. Slide 11

More Related