1 / 24

Nodal Analysis

Nodal Analysis. Objective of Lecture. Provide step-by-step instructions for nodal analysis, which is a method to calculate node voltages and currents that flow through components in a circuit. Partly covered in Chapter 5.5 Electric Circuits Fundamentals

kostya
Download Presentation

Nodal Analysis

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Nodal Analysis

  2. Objective of Lecture • Provide step-by-step instructions for nodal analysis, which is a method to calculate node voltages and currents that flow through components in a circuit. • Partly covered in Chapter 5.5 Electric Circuits Fundamentals • Chapter 9.4 Principles of Electric Circuits • Chapter 3.2 and 3.3 Fundamentals of Electric Circuits • Chapter 2.4 Electrical Engineering: Principles and Applications

  3. Nodal Analysis • Technique to find currents at a node using Ohm’s Law, Kirchhoff’s Current Law, and the potential differences betweens nodes. • First result from nodal analysis is the determination of node voltages (voltage at nodes referenced to ground). • These voltages are not equal to the voltage dropped across the resistors. • Second result is the calculation of the currents

  4. Steps in Nodal Analysis Vin

  5. Steps in Nodal Analysis • Pick one node as a reference node • Its voltage will be arbitrarily defined to be zero Vin

  6. Step 1 • Pick one node as a reference node • Its voltage will be arbitrarily defined to be zero Vin

  7. Step 2 • Label the voltage at the other nodes Vin

  8. Step 2 • Label the voltage at the other nodes Vin

  9. Step 3 • Label the currents flowing through each of the components in the circuit

  10. Step 4 • Use Kirchhoff’s Current Law

  11. Step 5 • Use Ohm’s Law to relate the voltages at each node to the currents flowing in and out of them. • Current flows from a higher potential to a lower potential in a resistor • The difference in node voltage is the magnitude of electromotive force that is causing a current I to flow.

  12. Step 5 We do not write an equation for I 7 as it is equal to I1

  13. Step 6 • Solve for the node voltages • In this problem we know that V1 = Vin

  14. Step 6 • Substitute the equations obtained using Ohm’s Law into the equations obtained using KCL.

  15. Step 7 • Once the node voltages are known, calculate the currents.

  16. From Previous Slides

  17. Substituting in Numbers

  18. Substituting the results from Ohm’s Law into the KCL equations

  19. Chugging through the Math • Node voltages must have a magnitude less than the sum of the voltage sources in the circuit • One or more of the node voltages may have a negative sign • This depends on which node you chose as your reference node.

  20. Chugging through the Math • The magnitude of any voltage across a resistor must be less than the sum of all of the voltage sources in the circuit. • In this case, no voltage across a resistor can be greater than 10V.

  21. Chugging through More Math

  22. Check • None of the currents should be larger than the current that flows through the equivalent resistor in series with the 10V supply. • Note that this check is only valid if there is one voltage source in the circuit.

  23. Summary Steps in Nodal Analysis 1. Pick one node as a reference node 2. Label the voltage at the other nodes 3. Label the currents flowing through each of the components in the circuit 4. Use Kirchhoff’s Current Law 5. Use Ohm’s Law to relate the voltages at each node to the currents flowing in and out of them. 6. Solve for the node voltage 7. Once the node voltages are known, calculate the currents.

More Related