1 / 41

PGA309 EVM Multi-Cal-Tools-V1.6a User’s Guide

PGA309 EVM Multi-Cal-Tools-V1.6a User’s Guide. Iven Xu April. 25 th , 2013 iven-xu@ti.com . Agenda. USB_DAQ and Multi-Cal-Tools overview Hardware configuration Software configuration. a) USB_DAQ and Multi-Cal-Tools overview. a) USB_DAQ and Multi-Cal-Tools overview.

kaleigh
Download Presentation

PGA309 EVM Multi-Cal-Tools-V1.6a User’s Guide

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. PGA309 EVM Multi-Cal-Tools-V1.6a User’s Guide Iven Xu April. 25th, 2013 iven-xu@ti.com

  2. Agenda • USB_DAQ and Multi-Cal-Tools overview • Hardware configuration • Software configuration

  3. a) USB_DAQ and Multi-Cal-Tools overview

  4. a) USB_DAQ and Multi-Cal-Tools overview • USB_DAQ Board Default Configuration:

  5. a) USB_DAQ and Multi-Cal-Tools overview • Multi-Cal-Tools Board:

  6. a) USB_DAQ and Multi-Cal-Tools overview • Multi-Cal-Slave Board(optional board):

  7. a) USB_DAQ and Multi-Cal-Tools overview • Multi-Cal-Interface PCA board:

  8. a) USB_DAQ and Multi-Cal-Tools overview • Multi-Cal-Interface Cable:

  9. a) USB_DAQ and Multi-Cal-Tools overview • Multi-Cal-Power Cable:

  10. a) USB_DAQ and Multi-Cal-Tools overview This is our test board, you can connect your PGA309 board to J* or T* of interface board. • Final setup overview:

  11. a) USB_DAQ and Multi-Cal-Tools overview • Multimeter: • Agilent 34401A (GPIB, Real RS232) • TH1961 (USB-to-RS232) • Our software “***.v1.6a” can support those three different interface • Download link: • ftp://ftp.ti.com/pub/linear_apps/Multi-Cal-PGA309/

  12. b) Hardware configuration

  13. b) Hardware configuration: • Step 1:

  14. b) Hardware configuration: • Step 2:

  15. b) Hardware configuration: This is our test board, you can connect your PGA309 board to J* or T* of interface board. • Step 3:

  16. b) Hardware configuration: • Step 4: (4-wire voltage output) Notes: (Same GND for the below two power supply) Power supply #1: • +Vdut =5V • -Vdut=GND Power supply #2: • +-15V • GND

  17. b) Hardware configuration: • Step 4: (4-wire voltage output) Notes: (Same GND for the below two power supply) Power supply #1: • +Vdut =5V • -Vdut=GND Power supply #2: • +-15V • GND

  18. b) Hardware configuration: • Step 5: (4-wire current output) Notes: (Float GND for power supply #1) Power supply #1: • +Vdut =24V • -Vdut≠GND Power supply #2: • +-15V • GND

  19. b) Hardware configuration: You can use your own Multi-meter with current measurement! • Step 5: (4-wire current output) Notes: (Float GND for power supply #1) Power supply #1: • +Vdut =24V • -Vdut≠GND Power supply #2: • +-15V • GND

  20. Extending the system with Slave Board:

  21. c) Software configuration

  22. c) Software configuration: • Windows 7 Attention

  23. c) Software configuration: • Press “Select Model File” to select correct model file. • Also, you can use “”Create Model File” to create a new model file.

  24. c) Software configuration: • Default Model Files for you:

  25. c) Software configuration: • Press “Start Cal” and then press the four Yes and Continue with Calibration

  26. c) Software configuration: • Press “Continue” to do the Fast Scan. • For the below picture, channel 0 and 1 is ok because I only connected two sensor modules to channel 0 and 1.

  27. c) Software configuration: • Press “Continue” to do the calibration • Below result was tested with TH1961 (with USB-232 rather than GPIB).

  28. c) Software configuration: • The other thing you need to pay more attention is “Address of TH1961”, • The current address of TH1961 we used is “COM 6”. • You need to change it in DMM script file. • Detailed step is in the below slides:

  29. c) Software configuration: • How to create a new model file to match the address of TH1961.

  30. c) Software configuration: • Take voltage output as an example: • Select “4wire_4p096_diode_USB.txt”

  31. c) Software configuration: • Take voltage output as an example: • Press “Edit DMM Script” and select “Voltage_TH1961_USB.txt”

  32. c) Software configuration: • Take voltage output as an example: • Change the COM port in the open script file. Make sure it is the same as your Multimeter(TH1961) address.

  33. c) Software configuration: • Take voltage output as an example: • After you change the script file, please save the file and re-select the script file again. Then press “save” to save the Model File.

  34. c) Software configuration: • Take voltage output as an example: • Save the Model File:

  35. c) Software configuration: • Select the new Model File, then you can press “Start Cal” to do the calibration.

  36. 4-wire voltage output result: • After the calibration:

  37. For current output: • Model File: • Iout_4p096_diode_USB.txt • DMM script file: • Current_TH1961_USB.txt • Also need to pay more attention on the address of DDM!

  38. Thanks!

  39. Back Up! If you are using Agilent 34401, pls see the below two slides of configuration files.

  40. If you use Agilent 34401A with GPIB: • Voltage output: • Model File: • 4wire_4p096_diode.txt • DMM script file: • Volt_34401_GPIB.txt • Current output: • Model File: • Iout_4p096_diode.txt • DMM script file: • Current_34401_GPIB.txt • Also need to pay more attention on the address of DDM!

  41. If you use Agilent 34401A with RS232: • Voltage output: • Model File: • 4wire_4p096_diode.txt • DMM script file: • Voltage_34401_rs232.txt • Current output: • Model File: • Iout_4p096_diode.txt • DMM script file: • Current_34401_rs232.txt • Also need to pay more attention on the address of DDM!

More Related