installation of n.
Download
Skip this Video
Loading SlideShow in 5 Seconds..
Installation of PowerPoint Presentation
Download Presentation
Installation of

Loading in 2 Seconds...

play fullscreen
1 / 15

Installation of - PowerPoint PPT Presentation


  • 117 Views
  • Uploaded on

Installation of. GSM. Car Alarm System. Congratulations for choose this GSM car alarm system for your car. Taking a few minutes to watch this Installation Guide and read the User ’ s Manual will be very helpful for the installation and operation on this GSM car alarm system.

loader
I am the owner, or an agent authorized to act on behalf of the owner, of the copyrighted work described.
capcha
Download Presentation

PowerPoint Slideshow about 'Installation of' - kairos


An Image/Link below is provided (as is) to download presentation

Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author.While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server.


- - - - - - - - - - - - - - - - - - - - - - - - - - E N D - - - - - - - - - - - - - - - - - - - - - - - - - -
Presentation Transcript
installation of

Installation of

GSM

Car Alarm System

slide2

Congratulations for choose this GSM car alarm system for your car. Taking a few minutes to watch this Installation Guide and read the User’s Manual will be very helpful for the installation and operation on this GSM car alarm system.

slide3

Never mount any parts or components outside the vehicle where it will be exposed to the elements. Never mount any component near hot or moving parts.

slide4

Always mount the components and route the wiring away from the rotating sterling shaft assembly. Except Siren, always mount the parts with 22” of the alarm module to assure the plug in cable reaches the parts..

slide5

First open the decoration board under the panel, select a secret place for installing the main module.In order that all parts’ wire can be mounted according to it’s position.

slide6

1)How install the GSMAntenna? It’s better to stick the Antenna on the surface of dashboard. Please refer to the picture “1 Antenna”, kindly note that the Antenna should be always towards the up. And the wire of the Antenna can’t be parallel to the large power cables (such as: turning light wire, or sub-woofer wire).

slide7

2)How to install the Microphone?Mount the microphone on the upper gap of Pillar between the windshield and the driver’s door. Please refer to the picture “2 Microphone”.

slide8

3)How to install the Voice Speaker?See the picture “3 Speaker”, it’s better to be mounted under the panel, find a suitable place and clean it, then tear off the 3M double-side glue on the back of the Speaker and stick it.

slide9

4)How to install the Valet Switch?Find a secret place on the pedal nearby the Clutch, drill a hole and fix the Valet Switch there. See the picture “4 Valet Switch”.

slide10

5)How to install the Shock Sensor?Since the RF receiver is also inside the shock sensor, it’s important that the Shock sensor should be installed away from the main magnetic sources, and keep it towards to the up. Mount the shock senor inside the Pillar which is nearby the driver’s door (or under the pedal). See the picture “5 Shock sensor”.

slide11

6)How to install the LED Indicator?Mount the LED indicator on the gap between the windshield and the dashboard where is easily seen from outside the vehicle. See the picture “6 LED”.

slide12

7)How to install the Start Kill Relay?Since the wire of the start kill relay is short, it’s better to fix it on the place which is convenience for connect it with the “start” wire of the Vehicle. Kindly refer to the “Wiring Diagram” of User’s Manual, connect the Start Kill Relay wire(green) with the “Start wire” of the Vehicle, connect the control wire(yellow) with 7-pin wire(white wire). See the picture “7 Start Kill Relay”.

slide13

8)How to install the Siren? Open the Hood of the Vehicle, and select a suitable place to fix the Siren by screw. Kindly refer to the picture “8 Siren”.

slide14

9)How to insert the SIM Card? After all the parts is mounted, make sure all the 7-pin and 12-pin wire is properly connected, then open the small slide cover on the back of the main unit, insert the SIM card. Then connect the wires of all parts into the main module, and turn on the backup battery. See the picture”9 SIM Card”.

slide15

10)How to install the Main Module?After SIM card, all parts and cable wires are all mounted and connected properly, fix the Main Unit. Please refer to the picture “10 Main Unit”.