Download
1 / 22
220 likes | 231 Views
Analysis of Irreversible Manufacturing Processes. P M V Subbarao Professor Mechanical Engineering Department. Special Parameter to Account Entropy Generation in MP…. T HS. Second Law for A Generalized Manufacturing System. Model Equations for Generalized Manufacturing System.
E N D
Analysis of Irreversible Manufacturing Processes P M V Subbarao Professor Mechanical Engineering Department Special Parameter to Account Entropy Generation in MP…..
THS Second Law for A Generalized Manufacturing System
Model Equations for Generalized Manufacturing System • Conservation of mass: • First Law • Entropy Balance:
SSSF Model Equations for Manufacturing System • Conservation of mass: • First Law • Entropy Balance: Thermal pollution generated by a Manufacturing Process
Design : Krishi Vigyan Kendra ,Jagdishpur, Sonipat 5KW design with 3.7KW Irrigation Pump
ADVANTAGES OF IIT Delhi DESIGN • Non-Renewable sources of petrol and diesel are not utilized • Whole system is noiseless and does not disturb the surrounding with sound pollution • Water flowing through the turbine (partial pressure design II) get oxygenated thereby effecting chemical and biological oxygen demands which have a bearing on self regeneration capacity of the soils [Pawlikewich] • A pump with a high discharge head could be utilized with this turbines hence Water storage in upper reaches facilitate ground water recharge. • The efficiency is the major player in power transmission and the water wheel is set to take on the costlier reaction turbines in its efficiency if it is properly worked on. • The whole irrigation system costs around 700$ range.
Effect of Planting methods on total irrigation time (hrs.) and yields of Cauliflower and Pigeon pea (Quintals /ha) Preliminary results show that farmers using the micro turbine pumped water supplies stand to gain US$ 2.25 / hour of pumping. Yhereby saving $53-73 in cauliflower and US$ 31-47 in pigeon pea. Raised bed planting improved the value of the produce by 10 percent.
Efficient Reuse of Low Quality water linked to Micro Hydro Irrigation charges @ $ 2.25 /h, amounts for savings as in cauliflower US$20/ha and pulse US$40/ ha on an average on the Whole Produce.{( KVK (HAU) , Sonepat,HARYANA,INDIA}
Generator Gear Box Main Shaft Canal Forbay Grinding Wheel Bush Bearing 12” Pulley 10” Pulley Grinder adjusting lever Penstock Water Wheel Wooden Base Workshop Powered by Pico-hydel Unit at Naya Gharat , Lacchiwala New Design
Impact of System irreversibility on actual Power consumption The quantity H-TS is backbone of thermo-economic/ecological analysis and is referred to as the Gibbs free energy.
Thermo-economics/Thermo-ecology • The quantity H-TS is known as the Gibbs free energy. • In manufacturing system, a different quantity appears, H - T0S. • The difference between this and the same quantity evaluated at the reference state is called flow exergy, B. • Exergy represents the maximum amount of work that could be extracted from a system as it is reversibly brought to equilibrium with a well-defined environmental reference state.
Exergy • In general, the bulk-flow terms may include contributions that account for both the physical and chemical exergies. • Hence = ph+ ch, as well as kinetic and potential exergy. • The physical exergy is that portion of the exergy that can be extracted from a system by bringing a given state to the “restricted dead state” at a reference temperature and pressure (T0,p0). • The chemical exergy contribution represents the additional available energy potential that can be extracted from the system at the restricted dead state by bringing the chemical potentials at that state (T0, p0) to equilibrium with its surroundings at the “ultimate dead state”.
Dead State • Consider a quantity of mass that undergoes a steady-state process. • With a given state for the mass entering the control volume, the reversible work will be a maximum when this mass leaves the control volume in equilibrium with the surroundings. • This means that as the mass leaves the control volume, it must be at the pressure and temperature of the surroundings, be in chemical equilibrium with the surroundings, and have minimum potential energy and zero velocity.
Actual and Ideal Power Consumption in terms of Flow exergy Second Law efficiency of a Manufacturing System
Degree of Perfection • DoP is defined as ratio of Exergy rate of useful products to Exergy flow rate of input material
